1mA-120A Electricity Meter Test Equipment 3 Phase Touch Screen

0.05 Class Three Phase Electric Meter Test Bench

Major Application and Functions:
1) Touch screen operation for control source panel
2) With standard meter together show all necessary parameters in one screen
3) Majorly used in automatic meter calibration setup (connect and disconnect of meter)
4) Calibration setup include two types: fixed load point and load point changing
5) Calibrate the meter through Genus software by applying control protocol offered. 6) With good power stability and high accuracy output
7) Can switch power factor between 1.0 and 0.5L, also phase angle can set & edit by end user. 8) Can switch four different balance & unbalance conditions 9) Independent output for each phase including voltage & current
10) Can ensure constant power output between connect and disconnect of meter. 11) Protection: current open circuit and voltage short circuit, etc 12) With PC communication port RS232

Output & Build time
Power build time for fixed load point setup: within 5 seconds Power build time for load change setup: within 10 seconds Power stability: 0.02% (value in the range) after power build
Set value to output value: Range ±0.05%, for P, Q, S, V, A, PF
Technical Details
1) Accuracy class of in-built standard meter: 0.05
2) Voltage Range: 3*(0-380V); Adjustable Range: 0-120%; Resolution: 0.01%
Output power: more than 200VA per phase; Distortion: ≤0.5%
3) Current Range: 1mA-120A; Adjustable range: 0-120% ; Resolution: 0.01%
Output power: 1000VA/phase; Distortion: ≤0.5%
4) Phase Angle: 0.00
o ~359.99
o
; Resolution: 0.01° 5) Frequency Range: 45-65HZ; Resolution: 0.01HZ
6) Indication display accuracy: 0.1% (voltage & current); 0.1°(phase); 0.01Hz (Frequency)

0.05 Class Three Phase Electric Meter Test Bench

Technical Parameters

0.05 Class Three Phase Electric Meter Test Bench

ARM alarm light connection definition

ARM main control board P2 PORT, 10-Cores connect to main control box where need to open a hole.install a 5 cores metal seat.

Both ends connection correspondence:

P2port 10-cores wire 5cores metal seat

2 feet +5V ------------------ 2 feet +5V

3feet green light(UO_10) ------------3feet green light

4feet yellow light (UO_9) ------------4feet yellow light

5feet red light(UO_11) ------------5feet red light

External control line board:LAMP_CTRLU.PcbDoc

Large 2 cores connect white 220v, black 0V,in parallel with power supply wire of standard meter.

Wiring diagram as below

External introduction light control circuit board:LAMP_CTRLU.PcbDoc

Configurations

1) Three Phases PS(Power source)

2) Three phase Standard meter, class 0.05 or 0.02 or 0.01

3)Meter Rack

      Number of positions: 6, 10, 12, 20, 40, 48....optional

      Each rack with one emergency STOP switch

      Each positions consist of 1 QCD 6 pins + 1 scanning head + 1 meter clamping + 1 RS/232/485

      communication port + 1 error display + 1  RESET button + 1 Set of voltage cable

      +1 ICT (need ICT or not depends on customer)

4) PC software

5) User Manuals

6) Optional

     0.05 Class Three Phase Electric Meter Test Bench

    - Isolated Current Transformer (ICT)

      Accuracy class: 0.01% (0.5C-1-0.5L)

      Current Ratio: 1:1 (1mA-120A)

      Current output: 3*(0.001-120)A (both primary and secondary)

       Secondary Output load: Maximum 0.5V (output current1mA-120A)

   -  MSVT

   - Personnel Computer

   - Printer