Micro Compression Force Sensor 50N 100N Miniature Loadcell 500N
200N
Micro Compression Load Cell FCCF is made of stainless steel based on strain gauge
technology offering 50N / 100N / 200N / 500N four rated capacities
intended for compression force measurement. Compact design with a
mounting base makes it easy to install the transducer, 1000ohms
high resistance minimizes the heat emission and improves long term
stability. Miniature size enables button load cell FCCF applicable
for appliations where mounting space is limited. You may find Miniature Compression Force Sensor FCCF suitable for applications such as load distribution
analysis, mold pressure measurement, force overload protection,
clamping force measurement, assembly force monitoring and so
on.
A Load Cell is a transducer that converts force acting on it into
electronic signal which is proportional to the applied force.The
acting force causes deformation of the measuring element,the bonded
strain gage deforms accordingly which will cause the resistance
change of the wheatstone bridge,under constant power supply,the
output signal between Sig+ and Sig- will change proportionally,thus
the force can be measured by measuring the output signal from the
load cell. Load Button Load Cell FCCF is designed to measure force in compression direction,outputs
millivolt signal within 0~22.5mV, and signal amplification may be
required for most applications, a load cell signal conditioner can
be used to convert mV signal into -5-5V, 0-10V or 4-20mA output
which is proportional to applied force.The amplified output then
can be easily processed by PLCs and data acquisition software. The
force can also be displayed through force indicator,force meter FPT
is integrated with high accuracy/low noise 24 bit Sigma-Delta
ADC,sampling speed up to 960Hz makes it suitable for both static
and dynamic measurement;FPT also supports Modbus RTU protocol with
RS485 or RS232 communication port,amplified signal
0-5V,0-10V,0-20mV or 4-20mA is also achievable from FPT.
Dimensions
| Ordering code | Measurement Range | Force direction |
| FCCF-50N | 0-11lbf / 0-5kgf | Compression |
| FCCF-100N | 0-22lbf / 0-10kgf |
| FCCF-200N | 0-45lbs / 0-20kgf |
| FCCF-500N | 0-112lbf / 0-50kgf |
Specifications
| Capacity | 50N / 100N / 200N / 500N 5kgf / 10kgf / 20kgf / 50kgf 11lb / 22lbs / 45lbf / 112lb |
| Rated output | 1.5mV/V |
| Excitation | 3-12V |
| Zero balance | ±0.1mV/V |
| Nonlinearity | ±1% of full capacity |
| Hysteresis | ±1% of full capacity |
| Nonrepeatability | ±0.5% of full capacity |
| Creep(3min) | ±0.3% of full capacity |
| Safe overload | 150% of full capacity |
| Ultimate overload | 200% of full capacity |
| Compensated temperature | -10...+40oC |
| Operating temperature | -20...+60oC |
| Temperature shift zero | ±0.05% R.O./oC |
| Temperature shift span | ±0.05% R.O./oC |
| Input resistance | 1000±100 ohms |
| Output resistance | 1000±100 ohms |
| Insulation resistance | >5000M ohms |
| Ingress protection | IP65 |
| Material of element | Stainless steel |
| Cable | Ø1.9*3000mm 4-core shielded cable |
| Wiring code | Red--Excitation+ Black--Excitation- Green--Signal+ White--Signal- |
Micro Compression Force Sensor 50N 100N Miniature Loadcell 500N
200N
Output signal of load cell and amplifier:
Load cell output: = (Power supply * Rated output) * Load / Capacity
Rated output of Button Load Cell FCCF is normally around 1.5mV/V.
Power supply of Miniature Load cell FCCF is normally within
3-15V.
Load / Capacity is within 0-1.
So the output range of Compression Type Force Sensor FCCF is
normally within 0…+22.5mV.
Example: Micro Compression Load Cell FCCF-50kg with 1.5mV/V
sensitivity powered by 10V DC,the output range is 0mV...+15mV.
The mV/V output from the wheatstone bridge sometimes can hardly be
processed directly, a signal conditioner can be used with the load
cell to deliver -5~5V, 0-10V or 4-20mA output.
Example: Mini Button Type Compression Load Cell FCCF-10kg working
with amplifier FSC(0-10V)-24V,the Load-Voltage relationship will be
0-10kg compression force VS 0-10V output, which is linear
regardless of the measurement error, 1V output corresponds to 1kgf
compression load, 2V output corresponds to 2kgf compression load,
and so on.
Click here to download datasheet
