Drilling Fluid Shear Pump Shear Polymer And Clay Special Sharp Edges

The drilling mud shear pump is the auxiliary equipment in the drilling fluids system. Drilling fluid shear pump is a solids control equipment specially used to shear polymer and clay, and it has been proven to be a piece of effective equipment practically and theoretically.

Specification of APJQB6545 shearing pump

Drilling mud shear pump is specially used to shear polymer and clay in drilling fluid. The polymer (or clay) in the drilling fluid system should be sufficiently cut in advance and then into the drilling fluid system, improve the performance of drilling fluid to give full play to its effectiveness. If not fully shearing, the polymer will block the shake screen in the first cycle. It will lose a massive amount of polymer, increase drilling cost, and may also make the large size of solid particles in drilling fluid difficult to be removed. Shear pump can make the polymer reduced by more than 15%, and the bentonite reduced by more than 30%. And it can also reduce mud cake and fluid loss, reduce drilling fluid shear rate, improve the gel strength, so as to achieve the advanced level of similar products abroad.

The polymer or clay in drilling fluid should be sufficiently cut before entering the drilling fluid system, which is helpful for a polymer to play an effective function and improve drilling performance. If the polymer is not fully cut, it may block the shale shaker screen in the first cycle and result in a large amount of loss, increasing the cost of drilling and making large size solid particles in the drilling fluid become hard and difficult to remove.

The shear pump is specially designed with the impeller holding jags to process the drilling mud mixed with clay and polymer. 

Details of drilling mud shear pump

The Shearing pump consists of impeller, casing, packing, shaft, belt, pulley, motor, base, and so on. The difference with other pump impellers is a more complicated structure. There are axial whirl flow, fluids reserve compartment, pump wheel, pressure cabin, shearing plate.

The axial flow whirl provides a certain quantity of fluids to the pump wheel and reserve cabin, 50% of this part fluids will flow into the reserved cabin, and the other half part flows into the casing. A pressure cabin is a special design to make sure fluids cabin holding drilling mud. The fluids flow is parallel to the shearing plate and introduces high flow velocity

Why select APJQB series shearing pumps?

There are many features of the shearing pump as follows. High efficiency, high flow rate, high lead, mechanical sealed. It can help get higher performance and better shearing effect. Faster hydration and dilution processes, meet the requirements of many different job sites. Saving the cost and time for users. For bentonite use, it can save cost up to 30%

Operating AIPU shear pump, the shearing, and hydration system will be a mature and complete system.

Shear pump for drilling fluids solids control

APJQB series Shear Pump is special-purpose equipment of solids control system which can meet all customers’ requirements of preparing drilling fluid for the well drilling. This shear pump manufactured by Aipu company is used to treat the high property mud, make the mud to obtain good rheological properties and cut the drilling cost as much as possible. This ideal solids control equipment designed by GN’s engineers has high performance and gained customers’ high evaluation.

Benefit and features

• Greatly enhance the degree of hydration of soil particles.
• Shear, dilute and hydrate polymer at high speed.
• With high displacement and lift, meeting the requirements of the drilling mud preparation and processing.
• With good sealing performance and high shearing efficiency.
• Matched with famous brand motor, superior performance, and guaranteed service life.
• Cast steel impeller, wear resistance, and good shear efficiency.
• Adopt five processes: grinding, sandblasting, epoxy zinc-rich primer, epoxy paint iron, polyurethane topcoat, which improve the corrosion life and beautiful craft of products.

Moreover, the shear pump can be customized according to practical working conditions and the user's special requirements. For example, it can be fit on a big rectangular base or a smaller base. And the vertical angle can be adjusted accordingly.

AIPU Solids control is a professional manufacturer engaged in shear pumps with rich experience. Our shear pump can mix high property drilling mud very soon. Decrease the mixing time by much and enhance the drilling efficiency with great cost control, shear pump helps much on high-quality drilling mud demand for a good drilling.

AIPU shear pump adopts a high-quality mechanical seal with high durability. There won't be any leakage. When drilling fluids flow past the shearing pump, there will be a second cutting on the 50% fluid in the swirl collection room. Sometimes clients will require a shearing mixing pump combined with a shearing pump and mixing hopper.

If you have any demand on drilling fluids shearing pump, Or you are interested in any other mud equipment. Please feel free to contact AIPU Solids. Trust you will get the real cost-effective solution at the best rate.