4W Electric Tying Machine

4W Power Vining Vegetables Plant Tying Machine Tool for Grapes Raspberries Tomatoes
 
 
High Quality Material: Gardening tying machine use Stainless Steel + Plastic.The weight of the strapping machine is about 546g. It is small and exquisite and it is very convenient to use.

Easy Operate: This tying machine makes trellising your plants much more efficient than using zip ties and cable ties. One hand operation, it can easily tie plants to support sticks and lines. Save labor costs and save time, easy operation, high efficiency.

 
Technical parameter:

Applicable battery and charger

►Due to our continuing program of research and development, the specifications herein are subject to change without notice.

►Specifications may differ from country to country.

►The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heaviest combination, according to EPTA-Procedure 01/2014, are shown in the table.

ACCESSORIES

►Charger

►hexagon bar wrench

►lubricant oil

►rope*2

FUNCTIONAL DESCRIPTION
CAUTION: Always be sure that the tool is switched off before adjusting or checking function on the tool.

Before turning on the power switch, always check that the charger is removed and that the binding arm of the tie machine is open.
►To start the tool, press the power switch and the power indicator is on.
►To stop use, press the power switch again, the switch will pop up and the power indicator is off.

TYING OD.
The maximum opening of the tie arm is the maximum diameter of the tie and the maximum tie must not exceed 50mm(1.96INCH), otherwise tool damage and / or possible damage.

ASSEMBLY
CAUTION: Make sure that the tool is powered off before performing any assembly operation on the tool.

Check the blade
►Before using the tool, check the blade for wear.
►Slow, worn blades can cause poor cuts, increase the difficulty of using the tool, and shorten its service life.

Adjust or replace the blade
CAUTION: The blade is very sharp, and the replacement or adjustment process must be very careful to avoid scratching your fingers.
►Press the handle slowly and check the upper and lower blades as normal, otherwise follow the method below.

1. Unscrew the inner hexagon screw with the attached hexagonal wrench；
2. Let the upper blade stick to the lower blade；
3. Re-tighten the inner hexagon screws.

►Make sure to use this thin washer when padded on some tool screws.
►When the upper blade is worn, follow the following method.
1. Remove the hexagon screw by using the attached hexagon wrench；
2. Remove the lock pin；
3. Remove the upper blade mounting seat；
4. Open the screw and replace the new blade；
5. After remounting the blade, install the blade.

Advantages of the tools:

SK5 STEEL WITH EXCELLENT QUALITY
SK5 steel engineering plastics, durable

EFFICIENT WORK
charging for one hour
can be used for more than one day

LUBE OIL, USE SITE
use smoothly without jamming

Install the rope

1. Remove the loading plate in the back direction.

2. Pull out the loading plate between left and right.

3. Install the new rope into the loading plate and press the loading plate.

4. Install the rope head up into the tool and wear the rope through the handle and arm according to the figure above (dotted line).Improper installation of rope may cause failure to tie properly or pull out difficult.

5. Press the handle to cut off the front material of the rope.

OPERATION

1. Turn on the power switch and open the tool binding arm.

2. Place the things to be tied into the binding arm.

3. Press the handle and release to secure the front end of the rope to the lower blade.

4. Open the binding arm and remove the binding arm along with the rope.

5. Press the handle again to the end, and the blade cut off the rope and wrap the rope.After the handle is pressed to the bottom, it should be kept for about one second. Too short time may lead to unwinding and loose release; too long time may lead to the winding belt fracture and the binding failure.

6. Release the handle and tie complete.

Product advantages:

Easy Operation
1. Half press to catch tape and then a full press to staple and cut. One hand operation, this binder machine can easily tie plants to support sticks and lines.

2. One hand operation, this binder machine can easily tie plants to support sticks and lines.

Labor saving
1. it can bind 3-4 times more plant than by hand in a unit time.

High efficient
1. it cost less time, so when farmers busy with the planting, we can have more time to do the other things like sprinkle.

SERVICE
1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
2. Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
3. Follow instruction for lubricating and changing accessories.
4. Do not modify or attempt to repair the appliance or the battery pack except as indicated in the instructions for use and care.

Applicaton

This tool is suitable for loose fixation of wires.Such as the branches of plants and stent fixation, multilinear beam fixation, etc.

Other pictures: