DC6V Garden Electric Tying Machine Plant Anti Slip Tape Tool Hand Tying Machine

Garden Plant Tape Tool Hand Tying Binding Machine Less Than 500G For Various Colors

Widely usage: It can be used for different kinds of plants such as grapes, tomatoes, cucumbers, peppers, flowers and so on.
Easy Operate: First you may pull out this then put the branch into it, press down and release the binding machine. Package your plants effectively.
Adjustable Width: The opening width can be adjusted at any time depending on the width you need which make your work more convenient.
Non-slip and ergonomic handle, labor saving, convenient to take and carry.
Made up of manganese steel, durable pressure foot and make you hooks more stable.

Specification:
Item Type: Garden Tape Tool
Material: Manganese Steel
Item Color: As Pictures Shown
Item Size: Approx. 34.3 cm / 13.5 inch
Package Weight: Approx. 688 g / 24.3 oz

Maintenance Method:
1. If the tying hand machine of the blade is not able to cut the belt, please use a long flat nose plier to pull out the used blade, and change a new one.
2. When the hand tying machine of stitching needle is blocked, you can use nipper or small screw driver to get it out. (If 1 section break into 2 section, we also can use one by one section avoid be blocked.)
3. Add lubricant oil to every joint after tying hand machine are long time using.

ACCESSORIES

►Charger

►hexagon bar wrench

►lubricant oil

►rope*2

Garden Electric Tying Machines DC6V

DC6V Anti Slip tape tool hand tying machine

FUNCTIONAL DESCRIPTION
CAUTION: Always be sure that the tool is switched off before adjusting or checking function on the tool.
Switch action

Before turning on the power switch, always check that the charger is removed and that the binding arm of the tie machine is open.
►To start the tool, press the power switch and the power indicator is on.
►To stop use, press the power switch again, the switch will pop up and the power indicator is off.

TYING OD.
The maximum opening of the tie arm is the maximum diameter of the tie and the maximum tie must not exceed 50mm(1.96INCH), otherwise tool damage and / or possible damage.

ASSEMBLY
CAUTION: Make sure that the tool is powered off before performing any assembly operation on the tool.

Check the blade
►Before using the tool, check the blade for wear.
►Slow, worn blades can cause poor cuts, increase the difficulty of using the tool, and shorten its service life.

Adjust or replace the blade
CAUTION: The blade is very sharp, and the replacement or adjustment process must be very careful to avoid scratching your fingers.
►Press the handle slowly and check the upper and lower blades as normal, otherwise follow the method below.

1. Unscrew the inner hexagon screw with the attached hexagonal wrench；
2. Let the upper blade stick to the lower blade；
3. Re-tighten the inner hexagon screws.

►Make sure to use this thin washer when padded on some tool screws.
►When the upper blade is worn, follow the following method.
1. Remove the hexagon screw by using the attached hexagon wrench；
2. Remove the lock pin；
3. Remove the upper blade mounting seat；
4. Open the screw and replace the new blade；
5. After remounting the blade, install the blade.

Install the rope
CAUTION: The tool shall use the specified rope.Other ropes may cause failure to install, tie failure, and / or damage the tool.
►The rope attached with this tool can be used directly and is an example of rope installation and a real sample reference for the purchase of rope.
►If the tie rope is out of replacement, follow the method below.

1. Remove the loading plate in the back direction.

2. Pull out the loading plate between left and right.

3. Install the new rope into the loading plate and press the loading plate.

4. Install the rope head up into the tool and wear the rope through the handle and arm according to the figure above (dotted line).Improper installation of rope may cause failure to tie properly or pull out difficult.

5. Press the handle to cut off the front material of the rope.

Steps of Operation:
1. Hold handle and press down with force, when you hear a voice of "da". the tape is hooked by hook, loose handle to take out the tape, pay attention that you can't use an excessive force.
2. The branch of crop need to bind overlap from wire and other materials, and tie both them with the tape, and quickly press down the handle by force.
3. After cut the adhesive tape off you should loosen the handle quickly and make redundant small tape to spring out.
4. Attention: Tape bound should be parallel with nail groove.

SERVICE
1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
2. Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
3. Follow instruction for lubricating and changing accessories.
4. Do not modify or attempt to repair the appliance or the battery pack except as indicated in the instructions for use and care.

Applicaton

This tool is suitable for loose fixation of wires.Such as the branches of plants and stent fixation, multilinear beam fixation, etc.