Miniature Load Cell 10N Tension Compression Force Measurement
Sensor 20N
Miniature Force Load Cell FSSM offers a compact design for a
variety of applications. the S Beam Load Cell series provides
accuracy, compact design features, offers 0-10N / 0-20N / 0-50N /
0-100N / 0-200N / 0-300N / 0-500N / 0-1000N eight rated measuring
ranges to choose from.The mini jr s beam load cell FSSM
utilizes metal foil strain gauge technology to deliver 2.0mV/V
output with maximum 0.1% non-linearity,the compact design enables s
type force sensor FSSM to be easily embedded into machinery or test
equipment – ideal for packaging machinery, assembly machinery or
end-of-line test equipment.The sensor features M3/M4 threaded holes
on two sides for the mounting of attachments or implements, this
micro load cell force sensor can be used for both tension and
compression force measurement in applications with limited mounting
space. You may find junior S beam load cell FSSM interchangeable
with FUTEK load cell LSB200,Mark Miniature Force Sensors Series
R04,flintec s-beam force sensor ISA,flintec force transducer
ISB,etc..
Specifications
| Capacity | 10N / 1kgf / 2.2lbf
20N / 2kgf / 4.4 lbf
50N / 5kg / 11lb
100N / 10kgf / 22lbf
200N / 20kgf / 45lbs
300N / 30kg / 67lbf
500N / 50kgf / 110lb
1kN / 100kg / 220lb |
| Rated output | 2.0mV/V |
| Excitation | 3-12V |
| Zero balance | ±0.05mV/V |
| Nonlinearity | ±0.1% of capacity |
| Hysteresis | ±0.1% of capacity |
| Nonrepeatability | ±0.05% of capacity |
| Creep(5min) | ±0.1% of capacity |
| Safe overload | 150% of capacity |
| Ultimate overload | 200% of capacity |
| Compensated temperature | -10...+40oC |
| Operating temperature | -20...+60oC |
| Temperature shift zero | ±0.03% R.O./oC |
| Temperature shift span | ±0.02% R.O./oC |
| Input resistance | 380±30 ohms |
| Output resistance | 350±5 ohms |
| Insulation resistance | >2000M ohms |
| Ingress protection | IP62 |
| Material of element | Stainless steel |
| Cable | Ø2*4000mm 4-core shielded cable |
| Wiring code | Compression@
Red--Excitation+ Black--Excitation- Green--Signal+ White--Signal- |
A force sensor is a transducer that converts force acting on it
into electronic signal which is proportional to the applied
force.The acting force causes deformation of the measuring
element,the bonded strain gage deforms accordingly which will cause
the resistance change of the wheatstone bridge,under constant power
supply,the output signal between Sig+ and Sig- will change
proportionally,thus the force can be measured by measuring the
output signal from the load cell.Tension and compression force
transducer FSSM is designed to measure force in both tension and
compression direction,outputs millivolt signal ranging -30~30mV,
and signal amplification may be required for most applications, a
load cell signal conditioner can be used to get -5-5V, 0-10V or
4-20mA signal proportional to applied force.The amplified output
then can be easily processed by PLCs and data acquisition
software.The force can be displayed through force indicator,force
meter FPT is integrated with high accuracy/low noise 24 bit
Sigma-Delta ADC,sampling speed up to 960Hz makes it suitable for
both static and dynamic measurement;FPT also supports Modbus RTU
protocol with RS485 or RS232 communication port,amplified signal
0-5V,0-10V,0-20mV or 4-20mA is also achievable from FPT.
Miniature Load Cell 10N Tension Compression Force Measurement
Sensor 20N
Click here to download datasheet
