Small Force Sensor 10N Miniature Force Transducer 10N Tension
Measurement
Miniature Force Sensor FSSM offers a compact design for a
variety of applications. the S Beam Load Cell series provides
accuracy, compact design features, offers 10N / 20N / 50N / 100N / 200N / 300N / 500N / 1000N eight rated capacities to choose from.The Miniature S Beam
Load Cell FSSM utilizes metal foil strain gauge technology to
deliver 2.0mV/V output with maximum 0.1% non-linearity,the compact
design enables the FSSM to be easily embedded into machinery or
test equipment – ideal for packaging machinery, assembly machinery
or end-of-line test equipment.The Lightweight S-type Force
Transducer FSSM features M3/M4 threaded holes on two sides for the
mounting of attachments or implements, this micro load cell force
sensor can be used for both tension and compression force
measurement in applications with limited mounting space. You may
find junior S beam load cell FSSM interchangeable with FUTEK load
cell LSB200,Mark Miniature Force Sensors Series R04,flintec s-beam
force sensor ISA,flintec force transducer ISB,etc..
Specifications
| Capacity | 10N / 1kg / 2.2lb
20N / 2kg / 4.4lb
50N / 5kg / 11lb
100N / 10kg / 22 lb
200N / 20kg / 45 lb
300N / 30kg / 67 lbf
500N / 50kg / 110lbs
1kN / 100kg / 220lb |
| Rated output | 2.0mV/V |
| Excitation | 3-12V |
| Zero balance | ±0.05mV/V |
| Nonlinearity | ±0.1% of capacity |
| Hysteresis | ±0.1% of capacity |
| Nonrepeatability | ±0.05% of capacity |
| Creep(5min) | ±0.1% of capacity |
| Safe overload | 150% of capacity |
| Ultimate overload | 200% of capacity |
| Compensated temperature | -10...+40oC |
| Operating temperature | -20...+60oC |
| Temperature shift zero | ±0.03% R.O./oC |
| Temperature shift span | ±0.02% R.O./oC |
| Input resistance | 380±30 ohms |
| Output resistance | 350±5 ohms |
| Insulation resistance | >2000M ohms |
| Ingress protection | IP62 |
| Material of element | Stainless steel |
| Cable | Ø2*4000mm 4-core shielded cable |
| Wiring code | Compression@
Red--Excitation+ Black--Excitation- Green--Signal+ White--Signal- |
A force sensor is a transducer that converts force acting on it
into electronic signal which is proportional to the applied
force.The acting force causes deformation of the measuring
element,the bonded strain gage deforms accordingly which will cause
the resistance change of the wheatstone bridge,under constant power
supply,the output signal between Sig+ and Sig- will change
proportionally,thus the force can be measured by measuring the
output signal from the load cell. Miniature Tension Compression
Load Cell FSSM is designed to measure force in both tension and
compression direction,outputs millivolt signal ranging -30~30mV,
and signal amplification may be required for most applications, a
load cell signal conditioner can be used to get -5-5V, 0-10V or
4-20mA signal proportional to applied force.The amplified output
then can be easily processed by PLCs and data acquisition
software.The force can be displayed through force indicator,force
meter FPT is integrated with high accuracy/low noise 24 bit
Sigma-Delta ADC,sampling speed up to 960Hz makes it suitable for
both static and dynamic measurement;FPT also supports Modbus RTU
protocol with RS485 or RS232 communication port,amplified signal
0-5V,0-10V,0-20mV or 4-20mA is also achievable from FPT.
Small Force Sensor 10N Miniature Force Transducer 10N Tension
Measurement
Click here to download datasheet
