ASTM E 662 Building Materials Burning Decomposition Density Of Smoke Testing Equipment
|
Detailed Product Description
|
Construction Materials Smoke Density Tester , Smoke Density
Apparatus Description: This instrument has been established for many years and is used
widely in all industrial sectors for the determination of smoke
generated by solid materials and assemblies mounted in the vertical
position within a closed chamber. This widely-used test instrument measures the specific optical
density of smoke generated by materials when an essentially flat
specimen, up to 25 mm thick, is exposed vertically to a radiant
heat source of 25 kW/m2, in a closed chamber, with or without the
use of a pilot flame. Standards: ASTM E 662 Standard test method of specific optical density of
smoke by solid material. BSI 6401 UK Standard of measuring specific optical density of smoke
by material. ISO 5659-2 Plastic smoke generation, determination of optical
density by a single chamber test. NES 711 Measure the smoke density index of a small specimen
burning. GB/T 8323.2 Plastic - Smoke generation - Part 2: Determination of
optical density by a single-chamber test. Features: 1. Integrated design. 2. 19" PC with Lab view. 3. Auto open ventilation up and down with cyclinder, control the
exhaust more efficiently. 4. Teflon coated inside, easy to clean and corrosion resistant. 5. Digital display of smoke optical transmittance and density. 6. Pre-heated apparatus for quick start up and accurate data
acquiring. 7. Safe blowout panel for safety, when the chamber pressure goes up
very quickly. 8. USA Medtherm Heat Flux meter, portable water cooling system
without running water supply. 9. Weighing sensor enables mass loss rate accurately. Specification: 1. Vent & Fan: Device for releasing combustion gases after test 2. Silicone Duct: Duct for releasing combustion gases 3. Conical Heater: Conical Heater for releasing 10 ~ 70 kW/m2 of
radiation heat 4. Shield Shutter: Shutter for blocking radiation heat before test 5. Heat Fluxmeter Port: Port for placing Heat Fluxmeter in the
center of Conical Heater 6. Pilot Flame: Flame allowing ignition of test specimen by
combustion gases 7. Specimen Holder: Holder for fixing 75 × 75 mm of test specimen 8. Load Cell Support: Support for placing specimen in the center of
Heater at an interval of 23mm 9. Load Cell: Load Cell for measuring mass loss rate of test
specimen 10. Portable water Cooling System Power Port : Power supply port of portable water cooling system for cooling
water of Heat Fluxmeter 11. Conical Heater Temperature Controller : Temperature controller for adjusting temperature of Conical
Heater 12. Chamber Heater Temperature Controller : Temperature controller for keeping the temperature of the inside
of Chamber at 34 ± 2 °C 13. Data Acquisition Program & PC : Program and PC for determining ignition time and mass loss rate
of test specimen using Remote Controller as well as radiation heat
(10 ~ 70 kW/m2) using Heat Fluxmeter 14. Size:1700(W)*750(D)*2000(H)mm Size of actual chamber: 914 mm ×
914 mm × 610 mm 15. Power Supply: 110/230 V - 50/60 Hz - 13 A 16. Weight:180KG |
| Product Tags: smoke density test apparatus astm e662 smoke density test |
Related Products
|
IEC 60243 Insulating Material Electrical Strength Testing Equipment |
|
ASTM D2843 Density Of Smoke Burning Or Decomposition Of Plastics Smoke Tester |
|
Deformation Of Plastics Under Load Testing Equipment GBT14483-1993 |
|
EN 1103 Textile Fabrics Ease Of Ignition Of Vertically Multifunctional Testing Equipment ISO 6940 |
|
ASTM E 662 Building Materials Burning Decomposition Density Of Smoke Testing Equipment |
|
Wire Smoke Density Chamber For Cables IEC 61034 Computer Controlled |
Email to this supplier