FT - CR2032- L5 3v Lithium Button Battery 210mAh , Environmental Friendly

Browse Categories

FORZATEC CO., LIMITED

City: changzhou

Province/State:jiangsu

Country/Region:china

Tel:86--13511662001

Contact Person:
Mr.Steve View Contact Details

Detailed Product Description

FT-CR2032-L5 3V 210mAh Laser Welded With Pins Li-MnO2 Button Battery

1.Scope

This specification governs the performance of the following WanQi 3V CR2032 button lithium battery.

2.Technique parameter

Item		Unit	Standard
Dimensions	Diameter	mm	20(-0.2)
	Height		3.2(-0.2)
Open voltage		V	3.1-3.45
Weight		g	3
Instant short-circuit current		mA	≥250
Nominal capacity(Load 15KΩ)		mAh	210
Appearance	The outward appearance is smooth,bright and clean, no rusty stain
Min time of discharge	Initial stage (New battery)	h	1000
	Delayed for 12 months		950
Over-discharge Characteristics		No leakage
Working temp/℃		-20～70
Storage temp/℃		-20～40

3.Test method

No.	Item	Condition
1	Dimensions	When measure with vernier calipers whose precision is up 0.02mm. to avord short circuit,should paste on one insulation material on one end of the vernier calipers
2	Open voltage	the precision of multimeters is not lower than 0.25%,intel resistance is bigger than 1MΩ
3	Instant short-circuit current	When test with multimeters, not surpass 0.5 second each time, avoid duplicating tests, if need once more, the time-gap should above half hour
4	Appearance	visual
5	Min time of discharge	Takes 9 batteries stochastically,Lay aside above 8 hours in the temperature of 20±2℃ and under the humidity of 60±15% conditions, with the condition that Resistance is 15 kΩ,end-point voltage is 2.0V. The new battery (Initial stage)should be tested in 60 days after produce. The old battery (Delayed for 12 months) should be tested in 14 days after the storage period.
6	Over-discharge Characteristics	Take nine battery in the temperature of 20±2℃ and under the humidity of 60±15% conditions, with the condition that Resistance is 15 kΩ,end-point voltage is 1.2V. visual test.

4.Acceptance rule

Check Criterion: ISO2859-1:1999(GB/T2828.1-2003),

The concrete item see the sheet of the following :

5.Cautions for Use

5.1 The battery shall be installed with its “+” and “-“ polarity in a correct position, otherwise may cause short-circuit.

5.2 Short-circuiting, heating, disposing of into fire or disassembling of battery is prohibited.

5.3 Battery can not be forced discharged, which leads to excess gassing and may result in bulging, leakage or explosion.

5.4 New batteries and used ones can not be used at the same time. It is recommended to use the same brand when replacing batteries.

5.5 Direct soldering is not allowed, or else it will damage the battery.

5.6 Battery are to be kept away from children. If swallowed, contact a physician at once.

6.Marks and Meanings of the words on battery surface:

1) ‘+’means battery positive pole

2) ‘CR2032’means battery model

3) ‘リチウムバシテリ－’means Lithium Battery

4) ‘3V’ means battery voltage

Product Tags: button cell battery 3v button battery

Related Products

Light Weight FT - CR2450- L9 3v Lithium Button Cell Battery 600mAh No Leakage

Email to this supplier


From:	Enter your Email please. Your email is incorrect!
To:	FORZATEC CO., LIMITED
Subject:	Subject is empty!
Message:	Characters Remaining: (80/3000) Please enter 20 to 3000 characters to contact this supplier!