Automatic Electric 1100W Metal Rolling Pipe Threading Machine Portable ZT-50BF

China Manufacture New Arrivals Automatic Electric Portable 1100W Metal Rolling Pipe Threading Machine ZT-50BF

Introduction

This machine is applicable to cutting, threading and inner hole chamfering (the chamferer is optional) of pipes for water, electricity and gas, and has the copying device able to automatically cut the standard taper pipe thread, with a reliable clamping device and an advanced cooling & lubrication system. Therefore, adopting this machine can lengthen the service life of the threading die, and avoid the deformation & slipping of the pipe clamp, so as to obtain the high-quality taper pipe thread. This machine is widely used in equipment installation, building and other industries, regarded as the ideal equipment to improve work efficiency, accelerate project progress, guarantee project quality and reduce labor intensity. (It is an ordinary round-steel threading machine, only applicable to the ordinary round-steel threading. The operating mode and machine structure are basically the same.)

Features

1. 1100W copper sensing motor, small noise, long use life, fulfillment of full-dimension thread at one time.
2. Exclusive hard tooth-surface high-speed gearbox, with small noise, long use life and high efficiency.
3. Jagged hammer panel design, firm clamp pipe, convenient operation.
4. Standard collocation of 50A multi-functional die head, die is replaced to process the round steel and wire pipe thread.
5. Double guide post cutting knife is accurate and durable.
6. Enhance type guide post trunnion can upgrade the stable properties of machine.
7. Large modulus oblique gear main shaft gear, super-large torque for easy transmission.
8. Selection of high efficiency, quality and performance-price ratio.

Technical data

Detail photos

How to Threading

(1) Pull the cutting knife frame and chamferer; put down die head to touch the copying block. After reliable positioning of die head, press the button to start the machine.

(2) Rotate the pipe in anti-clockwise direction, rotate the hand wheel of cutting feed, and make die head get close to the pipe.

(3) Apply force to the hand wheel of cutting feed, until die head makes 3 ~4 threads on the pipe.

(4) Then, loosen the hand wheel of cutting feed, so the machine starts automatic threading. When roller of die head goes over copying block and falls down, threading die will open automatically and the threading is completed (Z¹₃ T–M18 threading machine is required to turn back to make the threading die exit). Z1T–50A threading die shall be loosened manually.

(5) Machine halt. Return to the carriage, until the whole die head exits pipe end. Pull out die head, lock the handle and pull up the die head.

Important Notice

1. This machine shall be used with reliable grounding and anti-creep device.

2. Children are prohibited from touching this machine to avoid injury.

3. This machine shall not use the same socket with large-power machines, such as electric welding machine.

4. Pipe clamps shall not be installed on the machine, to avoid cracking of main components such as the cabinet.

5. Saponified solution shall not be used for cooling, such as water.

6. When above 2½″ pipe thread is made, it is required to adopt the low-gear processing mode,

7. When leaving factory, centrality of the machine has been measured, but pipes on the market have certain ovality at present. After machining, screw threads may be deep on one side and shallow on the other side. If they affect use, please check the quality of pipes.

Common Faults and Solutions

FAQ

1. How to get a accurate quotation from us?
Provide us the detail of the material such as metal thickness and width.
2. What’s the shipping cost from China to your country?
We can send machine to your port or door address by sea or airplane. Please kindly tell us your nearest port or address with postcode.We have reliable shipping agent to insure the safe, convenient and timely delivery.
3. Payment terms, MOQ, warranty, FOB?
Payment terms: 30% TT paid in advance, the balance of 70% before the shipment.
Minimum order quantity: 1 set.
FOB :Shanghai/Ningbo
Delivery time :7 days after receipt of formal order and 30% deposit.
Warranty:12 months.
4. What’s the package?
Fumigation-free plywood case.
5. What about commissioning service?
We can offer commissioning service, the buyer need to afford plane tickets.
6. What’s policy for guarantee and broken parts?
Warranty period of equipment lasts a year, during which the broken parts and spares caused by quality can be offered free.
7.Any question, call us or send email, we will try our best to satisfy you.