Automatic Electric 1/2 Inch Ridgid Pipe Threading Machine CE ZT-65BF

Automatic electric pipe threader CE ZT-65BF 1/2 inch ridgid pipe threading machine for sale

Introduction

This machine is applicable to cutting, threading and inner hole chamfering (the chamferer is optional) of pipes for water, electricity and gas, and has the copying device able to automatically cut the standard taper pipe thread, with a reliable clamping device and an advanced cooling & lubrication system. Therefore, adopting this machine can lengthen the service life of the threading die, and avoid the deformation & slipping of the pipe clamp, so as to obtain the high-quality taper pipe thread. This machine is widely used in equipment installation, building and other industries, regarded as the ideal equipment to improve work efficiency, accelerate project progress, guarantee project quality and reduce labor intensity. (It is an ordinary round-steel threading machine, only applicable to the ordinary round-steel threading. The operating mode and machine structure are basically the same.)

Features

1. Two-lever gear for high efficient threading.
2. Max capacity size to DN65.
3. 1300W copper induction motor. Low noise, durable use life, fulfillment of full-dimension thread at one time.
4. Jagged hammer panel design, firm clamp pipe, convenient operation
5. Standard collocation of swiff open type copying die hesa, automatic retraction, high efficiency
6. Double guide post cutting knife is accurate and durable
7. Thickened cast iron chuck for more confortable use.
8. Large modulus oblique gear main shaft gear, super-large torque for easy transmission.

Technical data

Detail photos

Operation guide:

A. Threading:

(1) Pull the cutting knife frame and chamferer; put down die head to touch the copying block. After reliable positioning of die head, press the button to start the machine.

(2) Rotate the pipe in anti-clockwise direction, rotate the hand wheel of cutting feed, and make die head get close to the pipe.

(3) Apply force to the hand wheel of cutting feed, until die head makes 3 ~4 threads on the pipe.

(4) Then, loosen the hand wheel of cutting feed, so the machine starts automatic threading. When roller of die head goes over copying block and falls down, threading die will open automatically and the threading is completed (Z¹₃ T–M18 threading machine is required to turn back to make the threading die exit). Z1T–50A threading die shall be loosened manually.

(5) Machine halt. Return to the carriage, until the whole die head exits pipe end. Pull out die head, lock the handle and pull up the die head.

B. Points for attention during threading:

(1) When threading die touches the pipe, gradually increase the force to tighten hand wheel of cutting feed until threading die bites 3~4 teeth into the pipe. If applying a small force to hand wheel of cutting feed and making it synchronize with threading die, higher quality threads will be produced.

(2) Pay attention to extension distance of the pipe. If it is too short, die head will collide with front chuck and the machine will be damaged.

C. Cutting:

(1) Pull up chamferer and die head to above the pipe.

(2) Put down cutting knife frame, and turn the cutting knife handle. Increase the opening of cutting knife frame, so roller of cutting knife frame strides over the pipe.

(3) Rotate hand wheel of cutting feed, and move the cutting knife to required cutting position.

(4) Rotate handle of cutting knife, so cutting knife and the pipe are clamped.

(5) Start the machine, slowly rotate the handle of cutting knife, so cutting knife blade cuts into the pipe. When the pipe is rotated for one circle or several circles, the handle of cutting knife is rotated for 1/4 circle.

After cutting is completed, exit feeding screw of cutting knife and pull the cutting knife frame to original position.

Warning: if the handle of cutting knife is rotated too violently, when cutting knife is cut into the pipe, the pipe may be deformed, cutting knife wheel may be broken and cutting knife seat may be cracked.

Common Faults and Solutions

Important Notice

1. This machine shall be used with reliable grounding and anti-creep device.

2. Children are prohibited from touching this machine to avoid injury.

3. This machine shall not use the same socket with large-power machines, such as electric welding machine.

4. Pipe clamps shall not be installed on the machine, to avoid cracking of main components such as the cabinet.

5. Saponified solution shall not be used for cooling, such as water.

6. When above 2½″ pipe thread is made, it is required to adopt the low-gear processing mode, 7. When leaving factory, centrality of the machine has been measured, but pipes on the market have certain ovality at present. After machining, screw threads may be deep on one side and shallow on the other side. If they affect use, please check the quality of pipes.

FAQ

1. How to get a accurate quotation from us?
Provide us the detail of the material such as metal thickness and width.
2. What’s the shipping cost from China to your country?
We can send machine to your port or door address by sea or airplane. Please kindly tell us your nearest port or address with postcode.We have reliable shipping agent to insure the safe, convenient and timely delivery.
3. Payment terms, MOQ, warranty, FOB?
Payment terms: 30% TT paid in advance, the balance of 70% before the shipment.
Minimum order quantity: 1 set.
FOB :Shanghai/Ningbo
Delivery time :7 days after receipt of formal order and 30% deposit.
Warranty:12 months.
4. What’s the package?
Fumigation-free plywood case.
5. What about commissioning service?
We can offer commissioning service, the buyer need to afford plane tickets.
6. What’s policy for guarantee and broken parts?
Warranty period of equipment lasts a year, during which the broken parts and spares caused by quality can be offered free.
7.Any question, call us or send email, we will try our best to satisfy you.