Automatic AB Epoxy Resin Dispensing Machine Robot Glue Dispenser
|
Detailed Product Description
|
Why Choose Us We Daheng Automation specialize in different types of potting and
dispensing system. No matter what your resin application
requirements look like: we can do most of them in our fully
equipped lab. We can handle 1- and 2-component polyurethanes,
epoxies, acrylics, silicones, temperature, humidity and UV curing
materials. They can be from low- to high-viscosity, filled or
unfilled and even high abrasive for thermal conductivity. Potting and encapsulation is the process of embedding products & assemblies in a liquid resin (potting compounds) to protect them against rough environment conditions. Potting can be performed in atmosphere pressure or even under vacuum, if high voltage insulation and high temperature differences are needed. Encapsulation of parts will stop corrosion of metals and reduce damage caused by vibration and mechanical stress. We offer automatic ,se-mi automatic fluid dispensing potting machine and the related production line and vacuuming systems . Introduction :1. Working Mode: controlled by PLC module and MCGS touch screen. 2.High precision valve: high speed, glue off clean, no glue
drawing, no dropping. 3. Core metering pump specially design for
different material from low to high viscosities. 4. Mix glue A
& B more evenly; no more or no less for agent B. Working principle :Compound materials A & B are kept in two tanks separately.
There are two sets of metering pumps inside the machine for
metering A and B resin by setting ratio, draining out material
individually from tank A & B. Liquid A & B mix with each
other in the mixer pipe and dispensed out according to the
programmable data. Tank system technology:1. Stainless panel vacuum pressure tank which can bear negative
pressure of inner tank . 2. Tank with motor stirrer that prevent
the glue from sediment and keep the potting material in constant
temperature. 3 Tank with top/ high /low liquid sensors that ensure
alarm warning when liquid higher or lower the setting level . 4
Tank with vacuum degas (degas time can be set through touch
screen), so the material can be re-feeding through vacuum negative
pressure . 5 Tank with pressure releasing ball valve ; the bottom
of tank reserved back-flow connector and river closure ball valve. 6 Tank with heater which can preheat materials to assure good
flowability . 7 Tank with artificial feeding mouth that can be
added glue appropriately by hand . 8 Tank with silica-dryer which
can prevent material especially PU from crystallization . D&H Pump technology1. Two cylinder plunger pumps work by durable motors. 2.The biggest
flow volume :24g/s,Repetition accuracy:0.2g. 3.Also Suitable for
high viscosity glue: 50cps~35000cps. 4. Suitable for big flow
dispensing or slight flow dispensing. 5. Suitable for frequent
start and stop dispensing. 6. Anti-wear, Anti-corrosion, super long
life time. Valve technology1. Two cylinder plunger pumps work by durable motors. 2.The biggest
flow volume :24g/s,Repetition accuracy:0.2g. 3.Also Suitable for
high viscosity glue: 50cps~35000cps. 4. Suitable for big flow
dispensing or slight flow dispensing. 5. Suitable for frequent
start and stop dispensing. 6. Anti-wear, Anti-corrosion, super long
life time. Tech Data
PLC Operation Controlling System 1 Dispensing volume is controlled by the speed of pump’s motors ;
Glue speed adjustable within the speed range . 2 Machine with detecting function that detect the speed and running
time of pumps to ensure the ratio reliability. 3 Adjustable gluing-out volume make sure glue A/B dispense out at
the same time from glue valve to get better glue mixing effect . 4 Machine with gel resistance calculator , which prevent the
mixture curing inside . 5 You can set single gluing-out and steady gluing-out function to
meet up with your different process requirement . 6 Whole machine system and function is controlled by Panasonic PLC
and MGCS touch screen . 7 Reserved PLC communication interface, which easy connecting with
outside device . 8 Equipped with a safety lock to prevent staff from wrong operation
. Application 1.Potting&Encapsulation &Casting: electronics componnets , PCB board, Capacitor, power supply,
transformer, ignition coil, reverse sensor, circuit board, filter
products ,underwater parts, electronic ballast ,aviation parts,
aerospace parts.... 2.Dispensing&Dosing : LED strip , led lamp , led bulb , aluminum,led screen , display
module ,medical parts,medical liquid filling .... 3.Bonding&doming : LCD screen ,LOCA bonding,ABS plastic,different types of stickers ,
badge , keychains , souvenirs ,arts , photo frame , and other arts
graphics.... Applicable material 1K and 2-component polyurethanes, epoxies, acrylics, silicones,
temperature, humidity and UV curing materials. Two component
potting materials , 2-part compound materials, AB part compound
materials , 2K silicones ,2K epoxies resin, Bi-component PU,
Ployerster, Polyurethane, UV materials and so on . Certifications Our Service Pre-Sales Service* Inquiry and consulting support. * Sample testing support. * View our Factory. After-Sales Service* Training how to instal the machine, training how to use the machine. * Engineers available to service machinery overseas. Packing & Delivery Our customer cases Service Term 1, Staff training Seller is responsible to provide machine’s training including
installation, debugging, maintenance to assured customer can
totally use the operation skills and well acknowledge maintenance
of machine . 2,Maintenance Service 2.1Seller provide one year warranty period and support free
maintenance service during warranty . Software upgrade service is
provided for a long life time. 2.2 In case parts of the machine become broken within the warranty
because of non-artificial factors, we send you part replacement
free, buyer pay for the shipment. Double-liquid valve should be
bought at its cost price. 2.3If the parts of the machine become broken past warranty , the
parts replacement should be shouldered by buyer. Other machines PGB-200Small automatic Glue dispensing machine with working area: L480mm*W480mm*H80mm QPD-300Glue dispenser for LED bulbs with 3 heads SZD-700One component glue dispensing machine with working area: L700mm*W700mm*H80mm PJL-1500Automatic glue mixing machine, manual glue dispenser PGB-1200automatic Glue dispensing machine with working area: L1200mm*W1200mm*H80mm PJL-1200Automatic glue mixing machine, manual glue dispenser, with long pipe |
||||||||||||||||||||||||||||||||||||||||||||||||||
| Product Tags: Automatic AB Epoxy Resin Dispensing Machine Robot Glue Dispenser AB Epoxy Resin Dispensing Machine | ||||||||||||||||||||||||||||||||||||||||||||||||||
Related Products
|
Daheng PGV-501 Precision Dispenser Auto Mixing Dual Curing Adhesives + 20MP Vision Capture System |
|
Automatic AB Epoxy Resin Dispensing Machine Robot Glue Dispenser |
|
Epoxy Dispensing Machine Liquid Dispensing System For Resin And Hardener |
|
Adhesive Dispensing Systems For Electrical Potting Compound |
|
Automated Glue Dispenser Epoxy And Hardener For Potting Epoxy For Electronics |
|
Manufacturing Plant Floor-Mounted Vision Epoxy Silicone Automatic Glue Dispensing Machine |
Email to this supplier