1. Application This machine equipment employs a combined forward pressure
application and reverse suction pressure mode of operation,
enabling it to meet the pressure testing requirements for
photovoltaic modules under extreme climatic conditions such as
deserts and plateaus. 2. Machine Picture Image above for reference only 3. Technical Parameter | Items | Description |
|---|
| Cylinder-type device | Allow the component sample to freely bend and deform under applied
load, ensuring the test surface pressure uniformity remains within
±5%. | | Pressure Method | Gradually and uniformly increase load until reaching the set value,
using both downward pressure and upward pull methods. | | Max sample size | 2600*1400mm(L*W) | | Cylinder Space | Cylinder space is adjustable | | Cylinder Type | Low Friction | | Cylinder Stroke | 400mm | | Cylinder Quantity | 72 sets (12*6) Enable free adjustment of suction cup spacing in
both horizontal and vertical directions at equal intervals. | | Cylinder distance | Cylinder Center Point Distance≤20cm | | Edge cylinder center distance from module edge≤20cm | | Deformation Detection | Infrared non-contact, deformation measurement range ±10 cm,
accuracy ±0.5 mm, with 7 points that can be placed at any position
within the same plan | | DC Stabilized Power Supply | Powering 1 Module; DC Power Supply: 120V 5A. | | Static Mechanical Load | Downward pressure: 800 Pa ~ 12,000 Pa; Upward pull: 800 Pa ~ 6,000
Pa; Setting at software | | Dynamic Mechanical Load | Downward pressure: -2,500 Pa ~ +2,500 Pa(Setting at software)
Cycle: 3~7 cycles/min | | Deflection Detection | Laser non-contact Measurement range≥10cm Accuracy±0.5mm Measurement
points: 5 point(can be placed at any position within the same
plane) | | Temperature Monitoring | Equipped one temperature sensor (OMEGA T-type thermocouple)
Calibration point: 25°C | | Controller | Capable of storing operational data, equipped with a USB interface,
enabling conversion of operational data into Excel/PDF files and
charts. | | Test pressure, cycle count, cycle duration, and energization
current; each pressurization process is independently programmable:
every test parameter for each cycle must be individually
configurable. | | Each suction cup's pressure can be individually controlled, and
pressure can be set separately. | | Including non-uniform snow loads, validated on top of previously
delivered loads. | | Collect test pressure, time, module deflection, real-time cycle
count, energized current, voltage, and module temperature data. The
sampling frequency is configurable. | | Using Touchscreen control Control panel can display real-time test
data curves; historical data and curves can be viewed on the
control panel; historical data can be exported to Excel. | | Safety Device | The air supply source equipped with a safety valve and status
indicator lights. In the event of a test failure, the device will
sound an alarm and halt the test. | | Air source | 0.6~0.8Mpa(prepare by user) | | Power | Single-phase, 220V, 50Hz | | Machine Dimension | Approx.,3700*2000*2300mm(W*D*H) | | Test Standard | | IEC 61215-2:2021 | MQT16 Static Mechanical Load Test | | IEC 61215-2:2021 | MQT20 Dynamic Mechanical Load Test | | ANSI/UL 1703:2018 | Mechanical Load Test | | IEC 62782: 2016 | Dynamic Mechanical Load Test |
Packaging & Shipping Simulation Animatronic Customer Triceratops are covered with air
bubble film before put them into the wooden case, which not only
has good shock absorption, impact resistance, heat sealing and also
has the advantages of nontoxic, odorless, moisture corrosion, good
transparency etc. Our Services If you face any problems in future during testing process we
promise we will give you a reply within 48 hours and solution
provide within 3 working days. We can offer operation video and
English operation muanual. We can provide video-conference. If
customers require on-site service, the transport and travel expense
shall be borne by customer. Pre-service 24 Hours online service for your consult. Help choose right model,and a series of service,person,advise. Middle service Give you best offer Provide discount for many sets order Do customer's request: Choose payment term you convienent. Promptly production and delivery,inform you in time. Can provide invoice value as you like to decrease your tax. After sale service 1 year warranty service and all life maintenance. Technical Egineer are avalible for oversea trainning. Free change for some parts Remote control technical consult Free installation DVD Maintenance plan Commitment: We will sign a letter of commitment while we sign the contract,
which will improve your confidence to us. Good Packaging: Good Packaging: Simulation Animatronic Customer Triceratops are
covered with air bubble film before put them into the wooden case,
which not only has good shock absorption, impact resistance, heat
sealing and also has the advantages of nontoxic, odorless, moisture
corrosion, good transparency etc.
|
