IEC 60601-1 Grips And Other Handling Devices-7 Cm Strap Tester

Suitable devices for the voltage, current/power and frequency

Supply: 1 phase and 3 phase variacs

Suitable devices for recording ambient temperature, humidity, atmospheric pressure

Environmental conditions: Climate chamber controlling temperature and humidity

Force gauge (30 N), standard test finger (figure 6), straight unjointed test finger, test hook (figure 7)

Illuminance meter

Distilled water, ethanol (96% pure), isopropyl alcohol , timer / stop watch

Oscilloscope, oscilloscope leads, suitable instruments for measuring voltage, current, capacitance, test pin (Figure 8), metal test rod (D = 4 mm, L = 100 mm), force gauge (10 N)

8.4.3,

8.4.4

5 kV test circuit & oscilloscope interface circuit according to Figures 9 & 10, oscilloscope

The test circuit according to Figure 11, oscilloscope, oscilloscope leads

Current source (25 A minimum, 50 or 60 Hz, 6 V maximum)

Measuring device according to Figure 12, mains isolation transformers, variacs, voltmeter, millivoltmeter, aluminium foil, diverse circuits (fig. 13-20)

High voltage tester, isolating transformer for HV-tests (fig. 28), stop watch / timer

Test equipment according to IEC 60695-10-2

Apparatus for ageing rubber in oxygen

Oscilloscope, oscilloscope leads, callipers, micrometer, spacing gauges, force gauge (2 N & 30 N), standard test finger (figure 6)

Test equipment according to IEC 60112

Heating cabinet

Force gauge (at least 100 N), torque gauge (at least 0.35 Nm)

Weights, angle gauge, radius gauge

5° & 10° inclined planes or inclinometer or trigonometric calculation, force gauge (at least 220 N), 20 cm by 20 cm test surface, weights, test threshold (10 mm high and 80 mm wide), 7 cm strap, stop watch / timer

The relevant tests of IEC 60065, Clause 18.

A-weighted sound pressure level according to ISO 3746, ISO 9614-1 or IEC 61672-1

Measurements are made in accordance with ISO 5349-1.

Hydraulic pressure test apparatus

Weights or load cell, 0.1 m² test surface, stop watch / timer, human body test mass (Figure 33)

Radiation meter

Radiation meter

Temperature indicator/recorder suitable for this function and

thermocouples, 4 wire resistance unit, test corner, variac

Spark ignition test apparatus (Figure 34), oxygen gas analyzer

15° inclined plane or inclinometer or trigonometric calculation, stop watch / timer, high voltage tester

Flask or graduated cylinder, stop watch / timer

Classification tests of IEC 60529

Dielectric strength and leakage current tests as appropriate

Sterilisation to client specification

stop watch / timer, voltmeter, ammeter, temperature indicator / recorder suitable for this function and thermocouples, 4 wire resistance unit, cheesecloth

Force gauge (250 N minimum), circular plane surface 30 mm in diameter, 500 g steel ball, 50 mm thick hardwood board (hardwood > 600 kg/m³), 40 mm step, hardwood doorframe (40 mm²), circulating air oven

Positive temperature coefficient devices (PTC’s) with IEC 60730-1: 1999, clauses 15, 17, J.15 and J.17

Performance of the tests identified in IEC 60086-4

Force gauge (at least 100 N), torque gauge (at least 6 Nm), stop watch / timer

Force gauge (minimum1 350 N), 30 mm diameter test tool, stop watch / timer

Classification tests of IEC 60529

Winding tester for transformers, temperature indicator/recorder suitable for this function and thermocouples variac, loads

5x voltage / 5x frequency dielectric strength test fixture, stop watch / timer

As in sub-clause 8.7

As specified in IEC 62471

4 mm & 12 mm diameter test rods, timer / stop watch, gasket test B-b of IEC 60068-2-2, force gauge (minimum 100 N), gas pressure meter (0 to 400 Pa range), voltmeter, ammeter, ohmmeter, meter for capacitance and inductance, vol/oxygen mixture (vol volume percentage 12,2 % ± 0,4 %),test apparatus for flammable mixtures (Figure G.7),

antistatic material testing according to ISO 2882