0.8-2.0mm Electrophoresis Aluminum Window Profiles Wood Grain Surfaces

6063 T5 Wood Grain Surfaces Aluminum Window Door Profiles Extrusion For Chile

Wood Grain Technology:

There are two types of wood grain transfer technology, one is water mark transfer technology, and the other is water drape transfer technology. The former mainly completes the transfer of characters and photo patterns, while the latter tends to complete the transfer on the whole product surface. In the introduction to printing industry written in 1973, it was pointed out that "Chinese printing was not invented by someone alone, nor was it suddenly invented in a certain era; It is the crystallization of the wisdom of thousands of sages, the accumulation of thousands of years of experience, and the collective creation of gradual comprehensive evolution and development.
”Cubic transfer uses an aqueous film that is easily dissolved in water to carry graphics and text. Due to the excellent tension of the water covered film, since the early Tang Dynasty, the middle Tang Dynasty, the late Tang Dynasty, the Five Dynasties and the Song Dynasty are overthrown by the existing literature and cultural relics, there is no need for further discussion of Beijing stainless steel. Therefore, this paper only briefly reviews and describes the four theories of the Han Dynasty, the Six Dynasties, the Sui Dynasty and Jiang Yuan.
Printing is a process technology, which transfers the wood grain on the printing plate to the substrate through transfer materials. It is easy to wrap around the product surface to form a graphic layer, and the product surface gets a completely different appearance like painting. Drape transfer technology can drape color patterns on workpieces of any shape. The switcher can solve the problem of three-dimensional product printing for manufacturers.
Curved surface coating can also add different lines on the product surface, such as leather grain, wood grain, emerald grain and dolomite grain. At the same time, it can also avoid the vacancy often seen in general board printing. In addition, in the printing process, because the product surface does not need to contact with the printing film, it can avoid damaging the product surface and its integrity.

Profile Specification:

Aluminum Profiles Features:

Corrosion resistance
The density of aluminum profile is only 2.7g/cm3, which is about 1/3 of that of steel, copper or brass (7.83g/ cm3, 8.93g/ cm3, respectively). In most environmental conditions, including in air, water (or salt water), petrochemistry and many chemical systems, aluminum can show excellent corrosion resistance.
conductivity
Aluminum profile is often selected for its excellent conductivity. On the basis of equal weight, the conductivity of aluminum is nearly 1/2 of copper.
Thermal conductivity
The thermal conductivity of aluminum alloy is about 50-60% of copper, which is beneficial to the manufacture of heat exchanger, evaporator, heating appliance, cooking utensil, cylinder head and radiator of automobile.
Nonferromagnetism
Aluminum profile is non ferromagnetic, which is an important feature for the electrical and electronic industries. Aluminum profiles cannot be self ignition, which is important for the application of handling or contacting inflammable and explosive materials.
Processability
The processability of aluminum profile is excellent. In various deformation and casting aluminum alloys, and in the various states after the production of these alloys, the machining characteristics have changed greatly, which requires special machine tools or technologies.
Formability
The allowable deformation is controlled by specific tensile strength, yield strength, ductility and corresponding processing hardening rate.
Recyclability
Aluminum has high recovery, and the characteristics of recycled aluminum are almost the same as that of primary aluminum.

Product Photos:

FAQ:

Q – What is the average lead time for pre production samples?

A – Our average lead time is normally 7 days for making new samples and 7 days for testing , totally need about 14days.

Q – What is the average lead time for mass production?

A – Our average lead time is delivery within 20-30 days after receive deposit and and moulds/samples are passed.

Q – What is CAD?

A – CAD stands for “computer assisted design” and it is a 3-D program that is used by our clients to provide our technicians with a three-dimensional example of the custom shape that they want made at GUANGDONG YONGLONG ALUMINUM.Aluminium Window Profiles

Welcome to visit our company !

Choose us & contact us !