AB 1746-OW8 ， SLC 500 Digital Contact Output Module
|
Detailed Product Description
AB 1746-OW8 , SLC 500 Digital Contact Output ModuleTechnical Specifications for 1746-OW8
About 1746-OW8The AB 1746-OW8 SLC 500 Digital Input Module comes with Eight (8)
outputs. This module has a voltage category of AC/DC Relay. The
operating temperature is -25-60 deg. Celsius (-13-140 deg.
Fahrenheit) and the nonoperating temperature is -40-85 deg. Celsius
(-40-185 deg. Fahrenheit) with a relative humidity from 5-95%
without condensation. The operating vibration of this module is 2g
at 10-500 Hz and the operating shock of this module is 30g. The AB
1746-OW8 has a maximum heat dissipation of 3.7 Watts with 0.138
Watts per point. The AB 1746-OW8 Digital Input Module has an operating voltage range of 5-125V DC and 5-265V AC at 47-63 Hz. The backplane current at 5V DC of this module is 85 mA. The backplane current at 24V DC of this module is 90 mA. The AB 1746-OW8 is supplied as open-type equipment. The 1746-OW8 is intended for use in industrial environments. This module should be installed in an environment with a pollution level no higher than Pollution 2 (as defined in the EN / IEC0664-1 publication) when applied in a Zone 2 environment. The enclosure should be accessible only by means of an appliance or tool. Do not disconnect equipment unless the power has been removed. Do not disconnect the equipment if the area it is in is dangerous. If this is disregarded, a dangerous electric arc will be created. The AB 1746-OW8 is an Eight (8) channel relay output module made by AB that is used with SLC 500 Programmable Logic Controller (PLC) platform. It is specifically compatible with fixed or modular style hardware for use with SLC 5/01, SLC 5/02, SLC 5/03, SLC 5/04 and SLC 5/05 controller. Use this module with operating voltage categories of 5 -125 VDC and 5 - 265 VAC. This module is divided into Two (2) groups with 4Four (4) channels per group to allow operation with different or same voltages. Surge suppression devices may be installed to maximize the module’s designed operating lifespan. Configure this module using RSLogix 500 programming software. Aside from SLC processors, this module is compatible for use in remote I/O topology. When used in Remote I/O chassis, slot 0 of the chassis is reserved for an SLC 500 communication adapter. Other slots are compatible for this module. With the use of the 1746-OW8, the need of interposing relays may be eliminated. Interposing relays are typically used for operation with different voltage category. As this module already support the mentioned capability, the need for interposing circuit is eliminated, saving panel space and increasing cost effectiveness. This module has similar signal delay rating of 10.0 ms for ON and OFF transitions at maximum resistive load. This module is certified for Class 1, Division 2 operation. The continuous current per module is 16.0 Ampere AC with 8.0 A per group. It occupies single slot of the chassis regardless of the installation location.
|
||||||||||||||||||||||||||||||||||
| Product Tags: 240VAC Isolated Relay Output Module PLCs Solid State Microcomputer Module ESCPP Positive Logic Output Module |
Related Products
|
ABB INNPM12 NETWORK PROCESSOR MODULE DCS Module +5VDC 10W MAX |
|
KJ3002X1-BA1 INPUT MODULE 8 CHANNEL 4-20 MA HART BUS POWER 12 V |
|
DI801 3BSE020508R1 INPUT MODULE DIGITAL 24 VDC 16 CHANNEL PLC Module |
|
ABB NTCL01 INFI-Net Communication Link TU Module Termination Unit |
|
Honeywell 51400955-100 Processor Control Board Multi Input Output Network Interface Board |
|
Honeywell CC-PAIX01 Analog Input Module 51405038-275 100MA 24VDC |
Email to this supplier