Ge Fanuc IC660BBD101 ， Low Leakage Input/Output Block ， 115 Volt AC
|
Ge Fanuc IC660BBD101 , Low Leakage Input/Output Block , 115 Volt ACProduct DescriptionIC660BBD101 is a GE Fanuc Low Leakage Input/Output Block that comes
with eight discrete points/circuits and delivers 115 Volts AC. The
input, as well the as operating voltage range, is between 93-132
Volts AC with a load current of 2 Amps. Each of its eight circuits
can be configured for either input or output. The I/O block links
multiple discrete sensors/actuators and a communication bus. The
block can accommodate high input impedance. A fuse shuts down
output current in the circuit if it goes beyond 30 Amps or 20 Amps
for every two cycles. The circuit can later be restored by issuing
a command from the CPU or a handheld monitor. The I/O block comes with features such as input filters with
selectable filter times ranging from 10ms -100ms, module control
for bus switching, output feedback for voltage monitoring, pulse
testing for output points, and defaults for output power-up. The
IC660BBD101 block comes equipped with salient diagnostics such as
voltage overload detection, power-off, and no-load detection. LED indicators on the I/O block blink to alert the user to errors
or faults such as faulty cabling, incorrect baud rate, and improper
grounding among others. There is a dedicated LED for each circuit.
For an output circuit, an LED, which in ON indicates that a
specific circuit has complied with the command issued by the CPU.
For an input circuit, however, an ON LED shows that a specific
terminal has reached the threshold voltage. Error messages are
generated on the handheld monitor, which helps the user attend to
the fault promptly and efficiently. The IC660BBD101 I/O block weighs 4lbs and works with model IC660HHM501 of the handheld monitor and IC693BEM331 bus controller model. During block mounting, the I/O block should be installed in a protective enclosure, which is clean and devoid of any contaminants. Furthermore, there should be adequate cooling space for the block. Mounting can be done right-side up or upside down.
|
| Rated Voltage: | 115 volt AC |
| # of Points: | 8 |
| Input Range: | 93-132 VAC |
| Load Current: | 2 Amps |
| Operating Voltage: | 93-132 VAC |
| Points per Common: | One group of 8 |
Technical Information
Specifications
Blocktype: CatalogNumbers: Block: TerminalAssemblyonly: ElectronicsAssemblyonly: | 8 circuit combination input and output
IC660BBD101 IC660TSD100 IC660EBD101 |
Size (height x width x depth): Weight: LED’s (I/O block): LED’s (each circuit): Block to Block Isolation: HeatDissipation: | 8.83” (22.44cm) x 3.50” (8.89cm) x 3.94” (10.00cm) 4 lbs. (1.8 kg) UnitOK,I / OEnabled On logic side of switch 1500 V 16W maximum with 8 inputs 43.5W maximum with 8 outputs on at 2 amps. |
Standbypower (all inputs and outputs off): Operatingvoltage(singlesource): Frequency: Power supplydropouttime: | 8.5 Watts 93–132 VAC 47–63 Hz 1 cycle (16.7mS at 60Hz, 20mS at 50Hz) |
InputCharacteristics: Non–tristate input, OFF state: Minimum voltage across input device (IN to H) Maximum leakage through input device Non–tristate input, ON state: Maximum voltage across input device (IN to H) Maximum switch current threshold Tristate input, OFF state: Acceptable voltage across input device (IN to H) Tristate input, ON state: Maximum voltage across input device (IN to H) Input load network: Resistor to N Capacitor to H Input processing time (typical) Selectable input filter times Inputdiagnostics |
60 VRMS |
| 1.5 mA | |
| 20 VRMS | |
| 6 mA RMS | |
| 16 VRMS–40 VRMS | |
| 4 VRMS | |
| 13K ohms | |
| .10 ïf | |
| 2mS + filter | |
| 10 to 100mS in 10mS increments | |
| Open Wire, Overtemperature, Failed Switch | |
OutputCharacteristics: Circuit output current (steady state) Maximum inrush current up to 2 cycles Maximum inrush current 2–6 cycles Maximum block output current Output Leakage @ 115 VAC: Current at 0 volt output (OUT to N) Voltage at open output (OUT to N) Output switch (OFF to ON / ON to OFF) Maximumswitching frequency Turn–on delay (maximum) Voltage drop (at 2 amps) Voltage drop (at 30 amps inrush) Recommended min. load, resistive (No Load disabled): Recommended min. load, inductive (No Load dis- abled): No Load enabled threshold Fusing Outputdiagnostics |
2 amps RMS |
| 25 amps peak | |
| 14 amps peak | |
| 15 amps at 35C, 7.5 amps at 60C | |
| < 7mA | |
| 65 volts | |
| Zerocrossing | |
| Once per second (high inrush currents) | |
| 0.5 Hz + 1mS | |
| 2.5 volts | |
| 10 volts | |
| 25mA | |
| 40mA | |
| 50mA | |
| Internal electronic short circuit trip. 100ms long time trip | |
| Short Circuit, Overload, No Load, Failed Switch, Overtemperature | |
Environmental: Operating Temperature Storage Temperature Humidity Vibration |
0 to +60 C (32 to +140 F) |
| –40 to +100 C (–40 to +212 F) | |
| 5% to 95% (non–condensing) | |
| 5–10 Hz 0.2” (5.08mm) displacement, 10–200 Hz at 1G |
|
ABB INNPM12 NETWORK PROCESSOR MODULE DCS Module +5VDC 10W MAX |
|
KJ3002X1-BA1 INPUT MODULE 8 CHANNEL 4-20 MA HART BUS POWER 12 V |
|
DI801 3BSE020508R1 INPUT MODULE DIGITAL 24 VDC 16 CHANNEL PLC Module |
|
ABB NTCL01 INFI-Net Communication Link TU Module Termination Unit |
|
Honeywell 51400955-100 Processor Control Board Multi Input Output Network Interface Board |
|
Honeywell CC-PAIX01 Analog Input Module 51405038-275 100MA 24VDC |