GE 10V Analog Output IC693APU301 / AXIS POSITION MODULE 1 AXIS Series 90-30
|
|
GE 10V Analog Output IC693APU301 / AXIS POSITION MODULE 1 AXIS Series 90-30
QUICK DETAILS
FANUC GE FANUC IC693APU301 DISCONTINUED BY MANUFACTURER MOTION MATE AXIS POSITIONING MODULE SERIES 90-30 PLC 24-PIN HIGH DENSITY CONNECTORS AVAILABLE REBUILT SURPLUS NEVER USED SURPLUS REPAIR YOURS 24-48 HOUR RUSH REPAIR 2 - 15 DAY REPAIR 2 YEAR RADWELL WARRANTY
OTHER SUPERIOR PRODUCTS
The Motion Mate APM is an easy-to-use intelligent, fully
programmable one-axis (IC693APU301) or two-axis (IC693APU302)
motion control module for the Series 90-30 PLC. The APM allows a
PLC user to combine high-performance control with PLC logic solving
functions in one integrated system. The APM can be configured to
operate in either Standard mode or Follower mode. When used in
Standard mode, it combines high-performance motion control with PLC
logic solving functions in one integrated system. When used in
Follower mode, it provides high-performance “electronic gearing”
for continuous master/slave applications. The desired mode is
easily selected by configuring a setup parameter in the
configuration software. The Series 90-30 and APM operate together as one integrated motion
control package. The APM controls axis motion and handles all
direct communications to the drive and machine while the PLC
automatically transfers data between PLC tables and the APM. The
PLC also provides a means for connecting Operator Interfaces, which
can control and monitor system operation. An example of an APM
servo system showing the hardware and software used to configure,
program, and operate the system is shown below. The APM can be
installed in any Series 90-30 CPU, expansion, or remote baseplate.
For embedded CPUs (311, 313, or 323), you may have up to three APM
modules. For a modular CPU (331 or higher), you may have up to
eight APM modules in one system, with a maximum of three APM
modules per baseplate. Multiple motion programs may be created and
stored in the APM (maximum of 10 may be stored in the APM) with the
Motion Programmer software package. The APM is configured and
programmed with VersaPro software (Version 1.1 or later) or Logic
Developer-PLC.
SIMILAR PRODUCTS
The APM faceplate (front panel) has two 24-pin high-density connectors for servo connections. The connector labeled A contains connections for Axis 1. Connector B, for a 1-axis APM, contains general purpose connections. Connector B, for a 2-axis APM, has connections for Axis 2 as well general purpose connections. To make wiring easier to the drive and machine, each high-density connector is typically connected by a short cable to a terminal block.
These cables consists of a 24-pin I/O connector , a cable, and a 25-pin D-type terminal block connector. (Cables are documented in Chapter 10.) Available cables are: IC693CBL311 (10 feet/3 meters) IC693CBL319 (3 feet/1 meter) IC693CBL317 (10 feet/3 meters) with an 8” external shield pigtail C693CBL320 (3 feet/1 meter) with an 8” external shield pigtail For building custom-length cables, the 24-pin I/O cable connector is available in three different kits (solder eyelet receptacle, crimp wire receptacle, and IDC (ribbon) receptacle). The terminal block is Weidmuller RD25 910648 or equivalent (must be compatible with the I/O cable IC693CBL311/319/317/320 - see Chapter 10 for details).
See the following manuals for detailed information on Power Mate APM Modules: GFK-0840 Motion Mate APM for Series 90-30 PLC Standard Mode User’s Manual GFK-0781 Motion Mate APM for Series 90-30 PLC Follower Mode User’s Manual GFK-0664 Series 90 PLC APM Programmer’s Manual
|
||||||||
| Product Tags: ethernet plc controllers industrial automation using plc |
|
EMERSON 01984-1540-0009 OI PROCESSOR PROCESSOR BOARD PCB ASSEMBLY |
|
ABB 1497-N9 250VA 600V 120V Voltage Transformer D521290 Controller |
|
2TLA020070R6600 SAFETY PLC PLUTO D45 WITH PLUTO SAFETY BUS ANALOG INPUTS 45 I/O 8 COMBINED |
|
2TLA020051R0200 SAFETY SENSOR UNIT W/3M CABLE W/M12 REPLACED BY 2TLA020051R5100 |
|
PLC Programmable Logic Controller Panasonic FP-Sigma series AFPG2543H |
|
Panasonic AFP7AD8 INPUT MODULE 8 ANALOG PLC Programmable Logic Controller |