Mitsubishi Industrial Servo Motor HF-KP43 with Gear Head AGX60-10 Reducer
|
|
Mitsubishi Industrial Servo Motor HF-KP43 with Gear Head AGX60-10 Reducer
Specifications for HF-KP43
Notes:
1.When the power supply voltage drops, we cannot guarantee the
output and rated speed. 2.80% ED at low noise. 80% ED: Indicates the condition in which operation time at read
torque accounts for 80% and the other no load time accounts for 20%
in a single operation cycle. 3.When the servo motor is equipped with reduction gear or
electromagnetic brake, refer to the corresponding outline dimension
drawing. For the EN Standard and UL/cUL Standard compliant models,
please contact Mitsubishi. 4.If the load inertia moment ratio exceeds the indicated value,
please contact Mitsubishi. 5.When the equipment is to be used in places where it is subjected
to oil and/or water, such as on machine field sites, optional
features apply to the equipment. 6.Except for the shaft-through portion and connector end. Cables
HC-MF23BK HC-MF23BK-UE HC-MF23G1-UE HC-MF23-S15 HC-MF23-UE INSTALLTION of Protection from oil and water (1) Next, the servo motor is not waterproof (IP44). Do not subject
the servo motor to oil and water. Especially for the HC-MF / HC-KF / HC-AQ / HC-KFS / HC-MFS and
HA-FF series, do not subject the shaft-through portion to oil. (2) When the gear box is mounted horizontally, the oil level in the
gear box should always be lower than the oil seal lip on the servo motor shaft. If it is higher than the
oil seal lip, oil will enter the servo motor, leading to a fault.
The HC-MF / HC-KF / HC-AQ / HC-MFS and HC-KFS series servo motor is
not equipped with an oil seal and cannot be used with the gear box
as described above. Oil should be shut off on the gear box side. (3) When installing the servo motor horizontally, face the power
cable and encoder cable downward. When installing the servo motor
vertically or obliquely, provide a trap for the cable. (4) Do not use the servo motor with its cable soaked in oil or
water. (Figure on the right) (5) When the servo motor is to be installed with the shaft end at
top, provide measures so that it is not exposed to oil and water entering from the machine side, gear box,
etc. (6) If the servo motor is exposed to oil such as coolant, the
sealant, packing, cable and others may be affected depending on the oil type. (7) In the environment where the servo motor is exposed to oil
mist, oil, water, grease and/or like, the servo motor of the standard specifications may not be usable.
Contact us. (8) In the case of the servo motor with oil seal, the oil seal may
sound during operation. It poses no problems in function.
Similar Products
Good Service in WTL:
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Product Tags: ewing machine servo motor electric servo motor |
|
75UMD301CACAA SERVO MOTOR UNIMOTOR UM 3000 RPM 75MM FRAME 6 POLE |
|
NTM-330-CBNS-0000 EMERSON Servo Motor NT 3 Inch 230 VAC 1.49 KW 4000 RPM |
|
C5050200STD PROCCESS CONTROLLER 85-265 VAC 50/60 HZ STANDARD BUILD |
|
MGE-455-CONS-0000 MG SERVO MOTOR 230VAC 3000 RPM MAX SPEED MS CONNECTORS |
|
MGE-316-CBNS-0000 MG SERVO MOTOR 230 VAC 3" FRAME 24 VDC BRAKE |
|
MGE-316-CONS-0000 MG SERVO MOTOR 230VAC 18.6 LB-IN CONT TORQUE |