10V~30VDC 0A-8A Brushless Dc Motor Driver JKBLD120 For 0-120w Bldc
Motor Suit motors: | Model | | Specification | Unit | JK57BLS01 | JK57BLS02 | JK57BLS03 | JK57BLS04 | | Number Of Phase | Phase | 3 | | Number Of Poles | Poles | 4 | | Rated Voltage | VDC | 36 | | Rated Speed | Rpm | 4000 | | Rated Torque | N.m | 0.11 | 0.22 | 0.33 | 0.44 | | Rated Current | Amps | 2 | 3.6 | 5.3 | 6.8 | | Rated Power | W | 46 | 92 | 138 | 184 | | Peak Torque | N.m | 0.33 | 0.66 | 1 | 1.32 | | Peak Current | Amps | 6.8 | 11.5 | 15.5 | 20.5 | | Back E.M.F | V/Krpm | 7.7 | 7.4 | 7.3 | 7.1 | | Torque Constant | N.m/A | 0.073 | 0.07 | 0.07 | 0.068 | | Rotor Inertia | g.c㎡ | 75 | 119 | 173 | 230 | | Body Length | mm | 47 | 67 | 87 | 107 | | Weight | Kg | 0.44 | 0.75 | 1 | 1.25 | | Sensor | Honeywell | | Insulation Class | B | | Degree of Protection | IP30 | | Storage Temperature | -25～+70℃ | | Operating Temperature | -15～+50℃ | | Working Humidity | 85% RH | | Working Environment | Outdoor (no direct sunlight), no corrosive gas, no flammable gas,
no oil mist, no dust | | Altitude | 1000 meters or less |
| | | Model | | Specification | Unit | JK60BLS01 | JK60BLS02 | JK60BLS03 | JK60BLS04 | | Number Of Phase | Phase | 3 | | umber Of Poles | Poles | 8 | | Rated Voltage | VDC | 48 | | Rated Speed | Rpm | 3000 | | Rated Torque | N.m | 0.3 | 0.6 | 0.9 | 1.2 | | Rated Current | Amps | 2.8 | 5.2 | 7.5 | 9.5 | | Rated Power | W | 94 | 188 | 283 | 377 | | Peak Torque | N.m | 0.9 | 1.8 | 2.7 | 3.6 | | Peak Current | Amps | 8.4 | 15.6 | 22.5 | 28.5 | | Back E.M.F | V/Krpm | 12.1 | 12.6 | 12.4 | 13.3 | | Torque Constant | N.m/A | 0.116 | 0.12 | 0.118 | 0.127 | | Rotor Inertia | Kg.c㎡ | 0.24 | 0.48 | 0.72 | 0.96 | | Body Length | mm | 78 | 99 | 120 | 141 | | Weight | Kg | 0.85 | 1.25 | 1.65 | 2.05 | | Sensor | Honeywell | | Insulation Class | B | | Degree of Protection | IP30 | | Storage Temperature | -25～+70℃ | | Operating Temperature | -15～+50℃ | | Working Humidity | <= 85% RH | | Working Environment | No direct sunlight, non-corrosive gas, flammable gas, oil mist, no
dust. | | Altitude | 1000m or below |
| Parameter | Min | Rated | Max | Unit | | Motor Hall Sensor Angle | 120°/240° | | | DC Power Input | 12 | 24 | 30 | V | | Drive Current Output | | 5 | 8 | A | | Suitable Motor Speed | 0 | | 20000 | rpm | | Hall Sensor Voltage | 4.5 | 5 | 5.5 | V | | Hall Sensor Current | | 20 | | mA | | External Potentiometer | | 10K | | Ω |
Mark | define | DC+/DC- | Power supply input (DC12V~DC30V)don’t make mistake for + and
- | U,V,W | Motor leading wires connect thick wires | Hu,Hv,Hw | Hall signal leading wire connect (thin
wires Hu, Hv, Hw) | REF+ | Hall power supply + (for motor hall input +5V) | REF- | Hall power supply - ( hall ground connect this port) | VCC | External potentiometer power supply port ( just can
use for potentiometer, can't for other external circuits) | SV | External potentiometer terminal ( See note speed
regulation )
| COM | common port ( Low level ) | F/R | Direction: dangling or high level forward, low-level inversion note 1 | EN | Enable: high level/stop
low-level/run note
1 | BRK | Fast brake: high level/stop
low-level/run note
1 |
|
