2HP Technical Teaching Equipment Experimental Heat Pumping Accumulation Simulator

ZM6192 Educational Equipment Technical Teaching Equipment Trainer Experimental Heat Pumping and Accumulation Simulator

• You should give an experience and train on temperature control, automatic pressure control device pressure, and automatic defrost.

  You should give an experience and educate theoretically about the automatic control of the refrigeration system and the refrigerator components.

  You must establish the temperature range measure to create the P-I Diagram, so that these experiments and training are available, such as equipment change cycles,Secondary heat exchange, through the heat accumulation tank.

  You should check and adjust the flow of the heating medium (Water)

  You must obtain the most accurate data through the high and low pressure switch.

  The heat accumulation tank must be able to be visualized through transparent acrylic and the thermotherapy must circulate through the circulator.

  It should be structured in order to accumulate heat, to be able to see the states and flow of the refrigerant, and to understand the principle of the components, so as to maximize the achievements of education.

  It must be composed of accessories, in order to visualize the state, principle and flow of the refrigerant.

  You must have the power control (ON / OFF), monitors and data stored in the computer of the electrical control panel, through software.

  Must have fault insertion and simulation

  User manual in Spanish with theory and practices for instructor and student

  Size: 1800x1400x1000mm

  Freezer main controller

  - Adopted 32-bit high-performance ARM processor

  - Built-in USB port for PC connection

  - Up to 16 temperature modules can be interlocked

  - Built-in RS-485 communication terminal for multipoint communication

  - The RS-485 communication circuit must be designed as an insulation structure to improve noise immunity.

  - 12-bit AD input for pressure and humidity sensor interlocked 16Ch

  - Built-in 16-channel digital input for function control.

  - 16 built-in LEDs to verify the output status inside the PCB

  - Built-in 16 external LEDs to verify the output status

  - Up to 16 relay output channels (8 basic channels, 8 optional channels)

  - The relay for the output must have a rating of 10 A or higher.

  - The SMPS and DCDC converter must be integrated and designed with an external signal and an insulation structure.

  - Power source: AC86 ~ 264V, 50 / 60Hz free voltage

  - Within the size of PCB 250X140

   

  It should contain the components listed below as:

  Compressor 1 / 2HP, Single Phase 220V, Control Box

  Air-cooled condenser, single phase 220V

  Evaporation pump and chamber with heat accumulation.

  1 / 2HP Liquid Receiver

  1 / 2HP accumulator

  Manual or welding expansion valve.

  Electronic valve for 3/8 ’operation with nut clamp, or welding.

  3/8 ’’ Filter Dryer with nut clamp, or welding.

  Pressure gauge: High pressure, Low pressure.

  High pressure switch, low pressure.

  Loading nozzles

  Acrylic visor, with nut or welding pliers

  Check valve (Welding)

  4-way valve (Welding)

  Refrigerator temperature module

  - Built-in 4Digit FND with good visibility

  - Up to 16 temperature modules can be interlocked

  - Built-in RS-485 communication terminal for multipoint communication

  - RTD type temperature sensor input

  - Accuracy within ± 0.2 degrees

  - Built-in 10A rating relay

  - Built-in 4-bit rotary switch for address configuration

  - Using a 10 A output relay

  - Power source: DC24V

  - Front PCB size within 70X50

Product Details and Warranty

We supply suitable spare pats according to experiment requirement, our products take aluminum structure, A4 paper dimension aluminum and plastic hanging box structure.

We supply 3 years warranty time.

Packaging & Delivery

Package details: plastic film+ plastic foam + plywood box with pallet, and for equipment dimension less than 1CBM, we supply plastic film+ plastic foam+ fine carton.

Arrange delivery within 45 days upon receipt of payment.

Please see below photo for detailed package.

Training Room Photo

Company Information

We supply professional educational training equipment and technical teaching equipment, which has been widely applied in Engineering Universities, Polytechnics, Technical Institute, Vocational Schools as well as Industry workforce Development Programs and Training Center. Our products allow students to learn and experiment through valuable hands-on experience, and the technology covered by our training equipment provides knowledge, experiments and didactic skills development that are of critical importance to today´s and tomorrow´s careers.

Photo for Clients Visiting Factory

Service

We supply supply7*24 hours service, customer design service, OEM service, buyer label service. With professional engineers team and sales team, we assure you good product quality.

Certificate
Our products takes ISO9001 product management system.