High Speed 9000 Sheets/Hour Automatic Overall and Spot UV Coating Machine
|
Detailed Product Description
|
High Speed UV Spot and Overall Varnish Coating Machine
Model: Ecoo SD-1060W
Product Description
Introduction:
The High Speed UV Spot and Overall Coating machine SD1060W adopts
upper-sway gripper-pass-sheet method to enable max speed up to 9500
sheets/hour. UV curing system with Teflon conveying belt has
characteristic of higher speed, precise orientation and UV curing
higher efficiency and lower power consumption. It is used for both
thick and thin papers, and can be used for both full and partial UV
varnish coating or water based varnish coating. Application:
Specification
Floor Plan: Coating with Anilox Roller: Coating with Rubber roller:
*Anilox roller is suitable for some high precision UV coatings, but different varnish thickness needs different lines of anilox
roller. * Rubber roller is suitable for different varnish thickness,varnish volume can be adjusted by the pressure between the rollers and metering of speed. It can do the varnish thickness up to 7g/m2 Rubber roller for example U.V Roller (Full) coating 1. Clamp and lock both ends of the rubber blanket. 2. Prepare a piece of paper (thickness: 0.5mm) or transparent film
for under spacing paper. 3. Hang one end of the rubber roller on the blanket clamp and
flatten the rubber blanket. 4. According to Inching, load the paper and hang another end of the
rubber blanket onto the other end of the clamp. U.V. Spot Coating 1. After the positioning by front lays and side lays, the middle
pass gripper catch and relay the paper into the paper gripping
mouth, and bring them into the pressure roller and the rubber
roller for impression by which the pasted U.V. varnish on the plate
will be coated on the paper surface which will be spot coated. 2. Prepare the paper sheet or transparent film with 0.5mm in
thickness for the use of transfer bottom board. 3. Lock the two ends of bottom board on the clamped board tightly. 4. Draw a straight basic line parallelly at the distance of 40 mm
from position C on the bottom board. When the bottom board is hung
on the rubber roller, this line should be on the same line of the
folded line of the rubber roller. 5. Take out a piece of paper to be coated, make an arrangement of
size of the to-be-coated part. Put the positive surface of the
to-be-coated paper on the working table, cut the part of the
to-be-coated paper, and then put the negative surface of the
to-be-coated paper on the bottom board.( At this time, the front
side of paper should be on the same line of the basic line or
forded line), draw the outline of the to-be-coated part on the
bottom board. 6. According to the cut part for coating of the paper, make a
rubber blanket of the same size or flexo plate which will be stuck
to the outlined bottom board with double-face glues. 7. Lock the bottom plate to the rubber roller and run the rubber
roller by inching to make another side of the bottom plate to
another clamp of rubber roller. Move the offset shaft with a wrench
to the top position and gripper both sides of the bottom plate and
make bottom plate stick to the rubber roller tightly. 8. The size of the rubber blanket: (perimeter) 820 x 1060mm(width) 9. Anilox Lines and Varnish Volume
Producing And Packaging
Installations worldwide
|
|||||||||||||||||||||||||||||||||||||||||||||||||
| Product Tags: High Speed UV Coating Machine Automatic Overall UV Coating Machine 9000 Sheets/Hour UV Coating Machine |
Related Products
|
B2 Digital Paper Sheet UV Spot Coater and Cold Foil Machine |
|
Automatic UV Spot Varnish Coating Machine 9000Sheets/H 730x1060mm |
|
1200mm UV Varnish Overall Full Coating Machine Factory |
|
9000sph UV Varnish Spared Spot Coating Machine With Anilox Roller |
|
1450mm Paper Waterbase UV Varnishing Machine Spot Coating |
|
Large Format Local Glazing UV Varnishing Machine 6200PCS/H |
Email to this supplier