| Model | SN4413-1400 |
| Inner Chamber | 1400mm*1400mm*1400mm |
| Outer Chamber | Approx. 1900mm*1560mm*2400mm |
| Outer Chamber Material | Spray treatment, concise, beautiful and smooth |
| Inner Chamber Material | High quality stainless steel plate |
| Weight | Approx.300KG |
| Turntable |
| Rotating Speed | 1 ~5 rpm adjustable |
| Turntable Diameter | 600mm |
| Turntable Height | Adjustable height: 200mm |
| Turntable Bearing Capacity | Max. 20KG |
| Turntable Function | IPX1 turntable parallel IPX2 can achieve 15° by adding the incline device on the turntable IPX3/4 turntable can rotation 360° |
| IPX1/2 Dripping |
| Dripping Hole Diameter | φ0.4 mm |
| Dripping Aperture Spacing | 20 mm |
| IPX1, IPX2 Dripping speed (water flow) | 1 +0.5 0mm/min(IPX1) 3 +0.5 0mm/min(IPX2) |
| Dripping Area | 1000X1000 mm |
| Distance between Drip Box and Sample | 200 mm |
| IPX3/4 Oscillating Tube |
| Oscillation Tube | R600 mm |
| Distance between Nozzle Sample | Within 200mm |
| Spray Aperture Spacing | 50 mm |
| Oscillating Tube Swing Angle | ±60° (IPX3), approximately ±160°(IPX4) (Note: standard requires IPX3:120°; IPX4:360°, but due to there is
turntable under oscillating tube during test, so 360° can not
achieved during actual testing, if without turntable, then 360° can
be achieved) |
| Angle Between Two Holes | 120°(IP3) 180°(IP4) |
| Needle Hole | φ0 .4 mm |
| Oscillating Speed | IPX3: 15times/min; IPX4: 5times/min |
| Water Flow of Each Hole | 0.07 L/min +5% |
| Spray Pressure | 80-150Kpa |
| IPX3/4 Spray Nozzle |
Nozzle Holes | 121 holes of Ф0.5mm 1 hole at the centre 1 inner circles of 12 holes at 30° pitch 4 outer circles of 24 holes at 15° pitch |
| Water Flow | 10L(min) |
| Spray Nozzle Spherical Diameter | 102 mm |
| Moving Shield Material | Stainless steel |
| Spray Nozzle Material | Brass |
| Handle and Valve Material | 304 stainless steel |
| Configured Pressure Gauge | 0～0.6MPa |
| Water Spray Pressure | 50～150(kpa) |
| Electrical Control |
| Controller | LCD touch controller |
| Test Time | 1-999,999min (can be set) |
| Turntable Control | Reduced motor, speed is stable |
| Oscillating Control | Stepping motor, oscillating tube swings stable |
| Flow and Pressure Control | Use manual valve to control flow and pressure, glass rotameters to
indicate flow, stainless steel case spring pressure gauge to
indicate pressure |
| Use Environment |
| Ambient temperature | RT10～35℃ (average temperature within 24H≤28℃) |
| Environment humidity | ≤85%RH |
| Power supply | 220V 50HZ single-phase three-wire + protective ground wire, the
grounding resistance of the protective ground wire is less than 4Ω;
the user is required to configure an air or power switch with
corresponding capacity for the equipment at the installation site,
and this switch must be independent and dedicated for the use of
this equipment |
| Power | Approx. 3KW |
| Protection System | Leakage, short circuit, water shortage, motor overheating
protection, alarm prompt |
