ISO 3795 Flammability Test Chamber For Automotive Interior Materials

Browse Categories

Electrical Appliance Testing Equipment(472)
Energy Efficiency Lab(52)
Vehicle Testing Equipment(171)
Battery Testing Equipment(93)
Test Equipment For Electric Lab(23)
Switch Life Tester(310)
Led Testing Equipment(84)
Water Ingress Testing Equipment(103)
Environmental Test Chamber(125)
Flammability Test Chamber(67)
MCB Testing Machine(26)
Medical Device Testing Equipment(38)
IEC 62368 Test Equipment(76)

Sinuo Testing Equipment Co. , Limited

City: guangzhou

Province/State:guangdong

Country/Region:china

Tel:86--13527656435

Contact Person:
Ms.Zoe Zou View Contact Details

ISO 3795 Flammability Test Chamber For Automotive Interior Materials

Brand Name	Sinuo
Model Number	SN776
Certification	Calibration Certificate (Cost Additional)
Place of Origin	China
Minimum Order Quantity	1
Price	Negotiable
Payment Terms	T/T, L/C, Western Union, MoneyGram
Supply Ability	10 Sets Per Month
Delivery Time	20 Days
Packaging Details	Plywood
Burner Material	Made of brass
Specimen Holder	U-shaped
Test Gas	natural gas, city gas, liquefied ga
Timer Accuracy	≤0.5s
Flame Height	38mm±2mm
Metal Comb	At least 110mm

Detailed Product Description

ISO 3795 Flammability Test Chamber of Automotive Interior Materials ASTM D5132 Horizontal Burning Rate Tester for Polymeric Materials

Overview:

This flammability test apparatus is intended for comparing the relative horizontal burning rates of polymeric materials used in occupant compartments of motor vehicles (cars, multi-purpose passenger cars, trucks and buses). It meets the requirements of ISO3795, DIN75200, ASTM D5132-17, TL1010, GB8410 and etc.

Principle:

The specimen is horizontally held on the U-shaped frame, and after the free end of the sample is ignited for 15 seconds in the combustion chamber using a predetermined height flame, it is determined whether the flame on the specimen is extinguished, or when it is extinguished, the burnt distance and the time to burn distance.

Technical Elements:

System Composition	Control devices, combustion chamber, burner, flow meter, specimen fixture, air pipe and fume hood
Control Devices	The control part is installed on the left side of the combustion chamber, which integrates timing, flow regulation, lighting, and fan on the control panel.
Flame Application Timer	0~999.9/S/M/H, can be preset, accuracy ≤0.5s
Burning Timer	0~999.9/S/M/H, accuracy ≤0.5s
Flame Height	38mm, observed through a 38mm flame height gauge, adjustable by flow meter
Burner	Inner diameter is 9.5 mm. It is located in the test cabinet so that the center of its nozzle is 19mm below the center of bottom edge of open end of the sample. It is made of brass and with auto ignition function.
Specimen Holder	U-shaped bracket: made of two U-shaped corrosion-resistant metal slabs, the upper bracket has 6 pin holes, the lower bracket has 6 pins, the support is in the form of 0.25mm diameter heat-resistant wires spanning the frame at 25mm intervals over the bottom U-shaped frame. The plane of the lower side of samples shall be 178mm above the floor plate. The distance of the front edge of the sample holder from the end of the chamber shall be 22mm, the distance of the longitudinal sides of the sample holder from the sides of the chamber shall be 50mm
Test Gas	The gas supplied to the burner shall have a calorific value of approximately 38MJ/m³, such as natural gas, city gas, liquefied gas
Metal Comb	At least 110mm in length, with seven to eight smooth rounded teeth per 25mm
Combustion Chamber	Length: 385mm, depth: 204mm and height: of 360mm. There are ten venting holes with a diameter of 19mm at the bottom of the combustion chamber. The four side walls have 13mm wide ventilation groove near the top. The top of the combustion chamber is provided with a hole for inserting a thermometer. The hole is arranged at the center of the top, and the center of the hole is 20 mm from the inner side of the rear panel. A collecting tray for collecting molten drippings is placed at the bottom of the combustion chamber, and the tray is placed between the two rows of venting holes without affecting the ventilation of the venting holes.

How to calculate the burning rate? Take ISO 3795 as an example.

The burning rate , B, in millimetres per minute, is given by the formula

B=s/t x60

Where,

s is the burnt distance, in millimetres

t is the time, in seconds, to burn distance s

Product Tags: flame test chamber flammability testing equipment

Related Products

IEC 60112 Leakage Tracking Test Equipment For CTI And PTI Evaluation Insulating Materials Test for sale


From:	Enter your Email please. Your email is incorrect!
To:	Sinuo Testing Equipment Co. , Limited
Subject:	Subject is empty!
Message:	Characters Remaining: (80/3000) Please enter 20 to 3000 characters to contact this supplier!

ISO 3795 Flammability Test Chamber For Automotive Interior Materials

ISO 3795 Flammability Test Chamber For Automotive Interior Materials

IEC 60112 Leakage Tracking Test Equipment For CTI And PTI Evaluation Insulating Materials Test

IEC 60884-1 Leakage Tracking Test Equipment Flammability Test For Insulating Material

IEC 60112 Proof and Comparative Tracking Indices Testing Equipment PLC Control Tracking Test Chamber

IEC 60950 A.3 Hot Oil Flammability Test Equipment for Fire Hazard Testing

UL94 Horizontal Vertical Flame Chamber with power 50W 500W Flammability Test Equipment

IEC 60332 Vertical Flame Propagation Test For Single Insulated Cable With PLC Control