Multi layers aluminum foil insulations for roofing, wall and floor
Introduction
Bagease Multi foil Insulation material provide good thermal barrier
property,but only with 38mm
thickness.Compared with the traditional insulation material,like
glass wool,foam,rock wool,our
material can not only seal your roof from the wind and dust as a
envelop,but keep the inside air
multi-foil insulation material can give you a very high thermal
barrier rate,7.17M2.k/w.
Bagease Multi Foil Insulation Material is a very flexible ,easy to
install and high performance thermal insulation material,in a 38 mm
thin,flexible,multi-layer blankets for roofs and walls. It is an
insulation solution complying with the highest insulation,
airtightness and vapour resistance performance while being only
38mm thick. It is ideal for roofs and attic conversions.
Bagease Multi foil Insulation material provide good thermal barrier
property,but only with 38mmthickness.Compared with the traditional
insulation material,like glass wool,foam,rock wool,our,material can
not only seal your roof from the wind and dust as a envelop,but
keep the inside air.multi.foil insulation material can give you a
very high thermal barrier rate,7.17M2.k/w.
Working Principle
The flow smoothly,providing you a good ventilation living
surrounding.after installing,your roof will
retain dry and warm in winter,while prevent overheating in
summer.The thickness is 38mm and
the beams and rafter can be lefted exposed,so our material will
save valuable living space in the attic.
Technology Data
Structure | Item | Value | Unit |
17 layers | Total layer number | 17 | layer |
Weight of polywool | 55 | g/m2 |
Thickness of EPE foam | 0.75 | mm |
Thickness of silver film | 12 | micron |
Quantity of silver film | 10 | layers |
Weight of both sides silver woven | 130 | g/m2 |
Strength of woven | MD | 580 | N/50mm |
CD | 580 | N/50mm |
Protective silver film | 12 | micron |
Emissivity of outer | 0.05 | |
Emissivity of inner | 0.05 | |
R Value of blanket | | |
Sewing size of stitches | Customized | |
Position of sewing | 5 | lines |
Thickness of finished material(well pressed) | Around 15 | mm |
Weight of finished roll | 10.8 | kg |
Square meter |
Aluminum Bubble Foil Heat Reflective Insulation Sheets for roof
floor an dwall
Product Introduction:
The product consists of three layers of aluminum foil with plastic
bubble laminated between the aluminum foil,provides excellent
insulation: Reflects up to 97% of radiant energy in addition to
resisting other types of heat transfer from conduction, convection
and radiation. The two side aluminum foil forms an effective
barrier against moisture, air currents and vapors.
It is an economical solution for a wide range of industrial,
manufacturing and consumer applications.
Bagease | Bagplastics |
Main Material | Alu + (single / double) PE bubble + Alu |
Other Material Structure | MPET + (single / double) PE bubble MPET + (single / double) PE bubble + MPET Alu + (single / double) PE bubble Alu + (single / double) PE bubble + Alu Alu + woven + (single / double) PE bubble + Alu Alu + woven + (single / double) PE bubble + woven + Alu Alu + woven + (single / double) PE bubble + Alu + Anti-glare
coating Alu + (single / double) PE bubble + woven + Alu +
Anti-glare coating |
Air Bubble Size | ¢ : 10mm, H: 2.5mm; ¢ : 10mm, H: 4mm; ¢ : 10mm, H: 6mm; ¢ : 20mm,
H: 7mm; ¢ : 25mm, H: 8mm; ¢ : 25mm, H: 10mm |
Coating Color | Blue, Green, Pink, Orange or customized |
MPET/ Al Foil Thickness: | 12micron/7 micron |
Product Thickness: | 2mm-10mm |
Reflectivity: | 96%~97% |
Normal Roll size: | 1.2m *30m/roll ; 1.2m *40m/roll; 1.35m *22.25m/roll; can be
customized |
Packing: | 1 roll/ clear plastic bag or customized logo printing packing bag
accept |
Data Sheet:
Material Structure: AL/Bubble/AL |
Bubble Size:D10mm*H 4mm(10*2.5/10*4/10*6/20*7/25*10)choose the bubble size |
Bubble Weight:130gsm |
Roll Width:1.2m (lenth can be customized) |
PROPERTIES | TEST DATA | UNIT |
Thickness | 3.5 | mm |
Weight | 256 | g/M2 |
Emissivity | 0.03-0.04 | COEF |
Thermal conductivity | 0.034 | w/m0 |
Apparent Density | 85 | kg/m3 |
Reflectivity | 95-96 | % |
Water Vapour Transmission | 0.013 | g/M2kpa |
Corrosion | doesn't generate | |
Tensile Strength(MD) | 16.98 | Mpa |
Tensile Strength(TD) | 16.5 | Mpa |
Installation methods and Installation Projects:
- Measure the metal roof to determine the amount of bubble foil wrap
insulation required for the project. Purchase approximately 10 to
15 percent more product than required to account for overlapping
and to provide the proper air gap between the purlins -- the
horizontal lengths of wood that support the roof panels between the
rafters.
- Cover the metal roof purlins with double-sided adhesive tape.
Unroll the foil wrap insulation and attach it to the first purlin.
Continue to unroll the foil insulation and attach it the remaining
purlins, paying attention to allow the insulation to sag at least 1
inch between the horizontal members. The sagging provides an air
gap that raises the insulation’s efficiency.
- Continue to attach the Aluminum foil bubble insulation to the metal
roofing purloins, overlapping the adjoining sheets 2 inches as you
go. This is a temporary hold to keep the bubble foil wrap in place
while you prepare the next step.
- Secure the bubble foil to the framing members with furring strips.
Attach the furring strips perpendicular to the purloins every 24
inches to the framing members with 2-inch metal screws, paying
attention to not disrupt the insulation’s sagging. Use a drill
equipped with a screwdriver bit to drive the screws into the
framing members.
- Cover the seams of the bubble insulation with foil tape.
Application:
Roof,Ceiling,Wall,Floor,Attic,Livestock Shelters,Basement,Factory
buildings,Duct wrappings,Container liner,Sun-stop cover and
vehicles.
1. Thermal insulation and light inflecting in the constrction and
protection for both cold winter and water piper
2. Separation of refrigerator,warm keeping for center
air-conditioned,refrigerator and other home appliances
3. Thermal insulation,sound absorption and noise reduction for car
,train, refrigerator car and laboratory, moisture proof cushion for
traveling.
Building insulation material for construction is a brand new heat
insulation product manufactured of polyethylene bubble/foam sheet
faced with aluminium foil on the one or two sides. It can reflect
97% radiant heat and reduces energy costs used in winter heating
and summer cooling. Reflective Foil thermal insulation is only a
few millimeters thick, its two sides of aluminium foil reflects
more than 97% thermal energy that reaches it .In summer, almost all
the sunlight and heat is bounced back into the air, Keeping the
heat out of the air conditioned building. In winter, Almost all the
heat generated inside the building is retained. Also, The
bubble/foam sheet in between the aluminium foil offer thousands of
empety air cells, which makes the heat more difficult to pass
through.1) Thickness: 0.017-0.03MM
2) Width: 300MM 450MM 500MM
3) Length: as your request
4) Color: transparent/clear,black,green,and so on
5) Net weight: on buyer's option
6) Packing: cartons or pallets.
Product features:
1.100% New material and accept sample order.
2.Excellence and beautiful, the high grade product.
3.Easy to be pulled out and cut.
4. Transparency and no drape and even thickness.
5. Easy to use, can be recycled.
PVA water soluble film
Specifications
Plastic Film
100% new raw material, LDPE , UV resistance
Thickness: 12 mic --50mic --300 mic .
Colour: Transparent, Black, Red, Blue, Green, etc.
The main products of the company are polyvinyl alcohol (PVA)
materials, films and bags etc. We have manufactured a series of
products of water-soluble PVA bags for various uses.It could be
processed according to customers demand of any size and
specification.the water-soluble PVA bags are divided into the inner
packing bags and the outer packing bags. Their characteristics are
as follows:
1,It will dissolve competely under the normal water
temperature(20±5℃) after 5-18 sec.
2,Its final products are CO2 and h3O, non-toxic and non-pollution;
3,The inner packing bags can dissolve completely above 3 ℃, while
the outer packing bags can issolve completely above 80 ℃.
4,Printing can be done on both the inner packing bags and the outer
packing bags, with clear handwriting, and oil ink and bags will
dissolve together.
5 The water-soluble bag has no static electricity, h3 stretching
intensity and even tensity .
6,The inner packing bags has heat sealing or tying with the
water-soluble rope, while the outer packing bags can have nylon
string and self-adhesive foil.
7,The size of water-soluble packing bags can range freely between
4cm*4cm---120cm*120cm.
8,Can be weighted exactly, no waste.