1000BASE-T Copper SFP Transceiver TX Disable and RX Los/without Los function

Features

• Up to 1.25Gb/s bi-directional data links
• Hot-pluggable SFP footprint

• TX Disable and RX Los/without Los function

• Fully metallic enclosure for low EMI

• Low power dissipation ( 1.05 W typical)

• Compact RJ-45 connector assembly

• Access to physical layer IC via 2-wire serial bus

• 10/ 100/ 1000Mbps compliant in host systms with SGMII interface

• Operating case temperature range of 0°C to +70°C (Commercial)

  -20°C to +85°C (Extend)

  
  

Applications

1.25 Gigabit Ethernet over Cat 5 cable

Description

TK-G3-RJ45 Copper Small Form Pluggable  (SFP)transceivers is high performance,  cost  effective  module compliant with the Gigabit Ethernet and 10/ 100/ 1000BASE-T standards as specified in IEEE 802. 3-2002 and IEEE 802.3ab, which supp- orting 1000Mbps data rate up to 100 meters reach over unshielded twisted-pair category 5 cable. The module supports1000 Mbps full duplex data-links with 5-level Pulse Amplitude Modulation (PAM) signals. All four pairs in the cable are used with symbol rate at 250Mbps on each pair. The module provides standard serial ID information compliant with SFP MSA, which can be accessed with address of A0h via the 2wire serial CMOS EEPROM protocol. The physical IC can also be accessed via 2wire serial bus at address ACh.

Pin Definitions

Pin Diagram

Figure 1. Pin Definitions

Pin Descriptions

Notes:

Plug Seq.: Pin engagement sequence during hot plugging.

1) TX Fault is not supported and is always connected to ground.

2) TX disable, an input used to reset the transceiver module, This pin is pulled up within the module with a 4.7 KΩ resistor. Low (0 – 0.8 V): Transceiver on Between (0.8 V and 2.0 V): Undefined

High (2.0 – 3.465 V): Transceiver in reset state Open: Transceiver in reset state

3) Mod-Def 0, 1,2. These are the module definition pins. They should be pulled up with a 4.7K~ 10K resistor on the host board. The pull-up voltage shall be VccT or VccR

Mod-Def 0 is grounded by the module to indicate that the module is present Mod-Def 1 is the clock line of two wire serial interface for serial ID

Mod-Def 2 is the data line of two wire serial interface for serial ID

4) RX_LOS (Loss of Signal): LVTTL compatible with a maximum voltage of Host_Vcc. RX_LOS can enabled or disabled (Refer to Ordering information),RX_LOS is not used and is always tied to ground via 100-ohm resistor.

5) RD-/+: These are the differential receiver outputs. They are AC coupled 100 differential lines which should be terminated with 100 (differential) at the user SERDES.

6) TD-/+: These are the differential transmitter inputs. They are AC-coupled, differential lines with 100 differential termination inside the module.

+3.3V Volt Electrical Power Interface

Low-speed signals, electronic characteristics

High-speed electrical interface, transmission line-SFP

High-speed electrical interface, host-SFP

General specifications

Mechanical Specifications

The host-side of theTK-G3-RJ45 conforms to the mechanical specifications outlined in the SFP MSA1.

The front portion of the SFP (part extending beyond the face plate of the host) is larger to accommodate the RJ-45 connector

References

1. Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA),September 2000.

2. IEEE802.3 – 2002.

3. “AT24C01A/02/04/08/ 16 2-Wire Serial CMOS E2PROM” , Atmel Corporation.

Regulatory Compliance

FQA :

1. Q: Are you a manufacturer?
A: yes, we are a manufacturer , FTTH solution and data center total solution provider in Shenzhen, China, established in 2000.

2. Q: What's your MOQ?
A: MOQ can be 1 pcs, but the price is not competitive.More quantity,the price will be more competitive.

3. Q: Can you quote FOB price?
A: yes. We can delivery by air, DHL, TNT, UPC, FEDEX, etc. For big quantity we will deliver it by sea.

We can quote price with freight and lead time for you, after you let us know detailed requirements with quantity.

We have competitive shipping forwarders. For more solutions, you can feel free to contact us.

4. Q: How is your quality?
A: Our production is according to IEC, Europe standard. CE, ISO, RoHS, CPR, and ANATEL certified.

All the products are 100% test before delivery.

5. Q: What's your lead time?
A: It depends on the quantity and products. For fiber optic patch cord, the lead time can be 2 -3 working days within 5000 pcs. We keep the regular products in stock. Also, we can deal with urgent orders.

6. Q: What's your warranty?
A: Depends one different product, we have1 years warranty for patch cord since delivery, but only responsible for non-artificial damage. For artificial damage, we can repair it for you for free, freight will be paid by your side.

7. Q: What's your packing?
A: International export standard package.If you need to print your logo on the packing, please let us know before we quote.

8. Q: Can you offer OEM/ODM?
A: yes, we can. all products accept OEM /ODM. we can sign the Confidentiality Agreement.

9. Q: Can I have a sample?
A: It depends on which products, Free sample provide under 10 usd. Freight will be paid by buyer before delivery.

10. Q: How can I order?
A:1. send mail or inquiries with product name, specification, and quantity to us . Provide your receive address if you need FOB,CIF,CFR price.

2. We will offer our quotation with lead time.

3. After the quotation confirmed, we will send a PI with our bank account.

4. Production will be arranged after the payment received.

5. Confirm the consignee with you before we deliver it.

6. The tracking number will be provided after the delivery.

11.what is your payment term?
A: T/T, Western Union, Paypal, MoneyGram at once. For big amounts, can be 50% deposit in advance, 50% balance paid before delivery.

With the same quality standard, if you could get better price from the market, TAKFLY also could support you same price.

3 years work experience in optical fiber industry, It's honored to be your professional product assistant.