Portrait PLC HMI Panel RS Protocol RS232 408MHz TFT Coolmay

275*194*36mm Portrait Display Integrated HMI PLC RS Protocol RS232

Parameter:

Advantage:

◆Upper computer programming software compatible with Works 2/GX Developer8.86 (supports Ladder diagram and SFC language, does not support structured programming/labels).

◆Powerful, compatible with FX3G/FX3U/FX3S PLC, high processing speed.

◆Military level 32 bit CPU adopted, which is faster and more adapted to industrial environment of high electromagnetic interference.

◆Special encryption, prevent illegal reading thoroughly. 8-bit encryption, 12345678 as password can thoroughly prevent reading of ladder logic program.

◆Clock supported, rechargeable battery adopted.

◆Default with 1 HMI download port, 2 PLC programming ports (RS232/MiniB USB port or Type-C), and one USB port.

◆PLC is optional to add 1 485 or 2 485(One of the 485 ports is changed from the default 232 port)/CAN/network port/WIFI(which will occupy the default port 232); HMI defaults to 1 RS232, optional 1 RS485. 

◆Support Mitsubishi programming protocol/MODBUS protocol/RS protocol/BD board protocol, easily realize PLC interconnection and communication with external devices.

◆High-speed counting, conventionally single-phase 6 channels 60KHz or AB (Z) phase 2 channels 60KHz + AB phase 1 channel 10KHz. High-speed pulse, conventionally 8 channels: Y0-Y3 is 100KHz, Y4-Y7 is 10KHz. High-speed counting+ High-speed pulse cannot exceed 480KHz; acceleration and deceleration are independent.

Network communication:

The network is automatically detected after power-on. When there is a network chip, M8193=1, the network is ready.

The involved special relays, special registers, and registers used by the IP address are as follows:

M8193:=1 Indicates that there is a network chip, and the network is ready

M8197:=1 Write the network address and reset automatically.

M8062:=1 Indicates MODBUS timeout, MODBUS_TCP is used.

M8063:=1 Indicates an IP address conflict.

D8395:Mitsubishi function and MODBUS_TCP switch

D8395=0:Mitsubishi function

D8395=1: MODBUS_UDP slave station

D8395=2: MODBUS_UDP master station

D8395=3: MODBUS_TCP slave station

D8395=4: MODBUS_TCP master station

D8395=5: EtherNet/IP slave (server)

D8397: When using MODBUS_TCP for ADPRW instruction, D8397 needs to be set to 3.

R23800 and 23801 are router addresses. The default is 192.168.1.1. That is, R23800=0XC0A8, R23801=0X0101.

R23802 and 23803 are the mask addresses, and the default is 0 .0. 0 .0. That is, R23802=0, R23803=0.

R23804~23806 are MAC addresses, which are generated by the system and are basically not repeated. Can also be set. Note: The MAC address on the same network cannot be repeated, otherwise it will cause abnormal communication.

R23807 and R23808 are the IP addresses of this machine. The default is 192.168. 1.250, that is, R23807=0XC0A8, R23808=0X01FA.

R23810 and R23811 are MODBUS target IP,

R23812 port default 502

R23813 default=100 (number of cycles), which is the interval time between WR3A and RD3A sequence execution.

R23814 default = 20 (200ms), it is the MODBUS timeout time setting, only retry twice, each time = (R23814*5)ms.

R23815 is the number of MODBUS sent packets

R23816 is the number of MODBUS received packets.