Container Spray Booth BZB Original Design Car Protable Paint Booth Quick Detail: The container spray booth is design for moving from one place to
another place easily,all assemble before delivery. | Container Spray Booth Configuration Table | | Telescopic room inside size | 6954(L)*4200(W)*2458(H)mm | | The outer diameter of the entire container | 10800(L)* 2438(W)*3400(H)mm(Close size) | | The outer diameter of the entire container | 10800(L)* 4354(W)*3400(H)mm(Expand Size) | | Main door | Front door with 2-leaf, 50mm thick EPS sandwich wall panels, size
2200×2400mm, (with large glass door), 6mm thick square tempered
glass observation window, glass size 1150x550mm. | | Safety door | 2 pieces, one for each side wall, 50mm thick EPS sandwich wall
panel, with pressure lock and observation window | | Equipment access door | 2 units, 50mm thick EPS sandwich insulation wall panel, size
2200x2200mm with pressure locks and cooling holes | | Outer frame | Square pipe, I-beam, channel steel, bending parts, corrugated board
and other welding machines | | Air intake chamber | Full-down draft, the top is a full filter cotton structure, and the
part near the cabinet is made with a mesh structure trawl | | Basement | - Two rows of standard floor grilles (galvanized), three rows of
checkered plates (painted)
- The bottom is sealed, and the platform bracket is welded to form
- 2000×900(L×W)3. Two pieces slope (with carrying ring), 2000×900
(L×W) painting
- The ground sealing plate of the back room is a panel checkered
plate with heat preservation
| Supply and exhaust system | 1.The cabinet board is filled with rock wool for heat preservation,
white, replacement the filter cotton and the normal inspection
surface is movable board (the top frame has a movable board on one
side) 2. Air supply: turbo fan DDF-7.5KW, direct drive ABB motor,
415V/50HZ/3PH 3. Exhaust air: TAE-450-7.5KW, belt drive ABB motor, 415V/50HZ/3PH 4,Generator group position: rear side | | Inlet and exhaust duct | Equipped with transfer ducts, 2 additional sections of air inlet
duct + rain cap; 4 sections of exhaust duct + gravity damper | | Filtering system | 1. Top filter: flame retardant 560G. 2. Ground filter: glass fiber cotton filter (green). - Exhaust filter: simple M-type filter cotton, no filter bag, no
environmental protection
| | Sealing board wall | 1.As shown in the three-dimensional diagram, the outside is welded
with corrugated board, and the inside of the room and the hot air
need to be added with 50mm EPS insulation board 2.Single side corrugated board for non-ventilated part of equipment
room | | Telescopic part | Manual push-pull telescopic track structure (2 people flexibly push
and pull, such as video) | | Heating system | 304 stainless steel heat exchanger, equipped with G20 diesel burner
heating, equipped with 4 smoke pipes and rainhat | | Lighting system | Australian external approach, 8 group of lower row lights | | Electric control system | Equipped with conventional Australian method electric control
system, star-delta start, with pressure gauge, wire color according
to Australian requirements, etc. | | Power supply | 415V,3phase,50HZ | Total power | 16.5KW | | | Remark | Optional gas heating FS20 burner | | | |
About Us:
JingzhongJing(JZJ) Group company was set up in 1999,now is a large
comprehensive company which
specialies in the design,manufacture,sales,service for
Pre-treatment,Painting lines and Exhaust Gas
treatment equipments.
Main Product:
Spray booth/Preparation room/Water testing line for
Car/Bus/Truck/Train/Boat/aircraft ect;Sand Blasting
Room/Shot Blasting Room/Power Coating/Painting line,Exhaust
gas(Vocs treatment equipment for all kind
of Industry Product ect.
Two Produce Base:
China South Produce Base (In Guangzhou,Since 1999)
China North Produce Base (Jiangsu,Since 2007)
Some of our Project.
----------------------------------------FAQs-----------------------------------------
Are you Trade company or manufacturer?
We are the manufacturer with export liscence.We have two factory in
Guangzhou and in Jiangsu,China.
How can we cooperation?
How can we cooperation?
1. Turn Key Project:
Our company will be responsible to help you to do the production
line desing,manufacturing,installation,
debugging and your personnel trainging jobs,Also we will provide
you one-stop service for your
production facilities procurement.
2. Equipment Supply:
Our company will not only provide you the equipments,but also will
offer you the onsite installation
instruction and guidance as well.
3. Other coopeation style.
Keep flexible and discuss.
How about after sale serivce?
1. Provide technical support and production line upgrade
2. Feedback withini 12h after receive fault notification or service
requirement
3. Free training on the user’s manual
4. User-friendly English manual or operation video for machine
using and maintanence.
5. On-the spot trainging and installation can be met if required.
6. On time delivery.
7. One Year Gruantee.
|
