Addition Platinum Cure RTV2 Silicon Rubber Transparent Liquid Silicone For Moulding
|
20 Shore A Clear Platinum Cure Mold Making RTV2 Liquid Silicone Rubber
Two-component addition type silicone rubber Silicone Rubber is a two-part, platinum-catalyzed, liquid silicone system that cures (RTV) to a Shore A 10~55 rubber. The polymerization can be accelerated by heat. The silicone components are delivered as liquids,which once mixed and cured transform into a transparent, elastic and resistant material. Polymerization occurs without formation of heat.
Features Outstanding release properties Cure can be heat accelerated High transparent appearance to cut split lines Very low shrinkage and good dimensional stability High hardness, but flexible and very tough Can be used for high temperature casting applications
Applications 1. A range of materials can be cast into the cured silicone mold: polyurethane and other reactive resins Small pieces of cement,plaster,concrete products. Food like chocolate,fondants Wax,candle,soap; Low melt metal 2. Label manufacturing, toys, jewelry, automotive, rapid prototyping etc.
1. Mixing the two components According the mixing ration 10:1 weighting A and B, the two components may be thoroughly mixed either by hand or using a low-speed electric to minimize the degassing of bubbles and to avoid any temperature increase. Note: It is also possible to use a special mixing and dispensing machine for the silicone components, further information is available upon request.
2. Moulding The mixture should be degassed preferably at 30 to 50 mbar to eliminate any entrapped air. If a dispensing machine is used, the two components are degassed separately prior to mixing. The silicone mixture expands to 3-4 times of its initial volume and bubbles rise to the surface. The bubbles progressively disappear and the mixture returns to its initial volume after 5 to 10 minutes. Wait a few minutes to complete the degassing and then flash the vacuum. The silicone is ready for pouring, either by gravity or under low pressure.
Note: Flashing the vacuum once or twice accelerates the degassing. It is recommended to use a container with a high diameter/height ratio (3 to 4 times of the initial volume)
3. Polymerisation The curing may be slowed down at lower temperature or accelerated by applying heat. Note: 1. Contamination from sulfur (e.g., sulfur-based clay), amines, tin compounds, cured polyester resin, some paints and some silicone rubbers may inhibit surface cure of platinum-cured rubbers. 2. Apply a release agent, Although not usually necessary, a release agent will make demolding easier when casting into most surfaces.
Packaging 20kg per drum, 200kg per drum
When the silicone rubber is stored at or below 25 degree Celsius in the original unopened containers, Silicone Base and Curing agent have a usable life of 12 months from the date of production. After 12 months’ stockpiles, please use tool to stir the Part A silicone for some minutes, then the silicone can be use again, no influence for other performance. 1. Store the original packing tightly sealed and at a temperature below 25 degree Celsius.Use the product as soon as the packaging has been opened. 2. Close the lid tightly after taking out the proper amount of liquid silicone rubber. Use the product as soon as the packaging has been opened.
|
| Product Tags: Clear Platinum Cure RTV2 Silicon Rubber Transparent Liquid Silicone For Moulding 20 shore A Transparent Liquid Silicone |
|
High Viscosity Platinum Silicone Rubber For Angel Wings Silicone Mold Viscosity 7000-9000 cps Mix ratio 1 1 |
|
Platinum Silicone Rubber For Mermaid Tail Sugar Art Cake Decoration Silicone Mold |
|
Translucent Platinum Silicone Rubber For Starfish Shell Resin Silicone Mold |
|
0 Shore A Platinum Silicone Rubber For Cream-pointed Silicone Mold |
|
10 Shore A Platinum Silicone Rubber for Rose Resin Silicone Mold 30-40 Minutes Working Time 3.8-4.0 Mpa Tensile Strength |
|
10 Shore A Platinum Silicone Rubber for Rose Silicone Mold High Tear Strength 15-17 N/mm and Viscosity 7000-9000 cps |