Efficient Energy Saving HVM Series Coal Vertical Roller Mill For Powder Plant

Efficient Energy-saving HVM Series Coal Vertical Roller Mill For Powder Plant
 
Product Introduction

Pulverized coal vertical mill is a new type of high efficiency, energy-saving and widely used grinding machine, which can be used in industries such as cement, electric power, chemical industry, non-metallic minerals, etc. It is widely used in the non-metallic mineral industry in the cement industry at home and abroad due to its advantages such as high efficiency, low power consumption, large drying capacity, easy adjustment of product fineness, uniform particle size, easy control of chemical composition, low noise, small metal wear, no dust, simple system process flow, small floor space, and low investment.

Main structure and functions:
HVM type vertical mill is mainly composed of separator, grinding roller, grinding plate, pressure device, reducer, motor, housing, etc.
The separator is an important component that determines the fineness of a product. It is composed of a variable speed transmission device, wheels, guide vanes, housing, coarse powder blanking cone, air outlet, etc., and its working principle is similar to that of a powder concentrator.
The grinding roller is the main component for rolling and grinding materials. There are two pairs of grinding rollers installed in the mill, each pair of which is mounted on the same shaft and rotates at different rotational speeds.
The grinding plate is fixed on the output shaft of the reducer, and the upper part of the grinding plate is a material bed with an annular groove.
The pressurization device is a component that provides grinding pressure, consisting of a high-pressure oil station, a hydraulic cylinder rod, and an accumulator. It can apply sufficient pressure to the grinding roller to crush the material.
In addition to transmitting power, the reducer also bears the weight and grinding force of the grinding plate.

【Working Principle】

The motor drives the grinding plate to rotate through the reducer, the material falls in the center of the grinding plate from the feed port, and the hot air enters the mill from the air inlet. Under the action of centrifugal force, materials move towards the edge of the grinding plate. When passing through the circular groove on the grinding plate, they are crushed by the grinding roller. The crushed materials are carried away at the edge of the grinding plate by the high-speed airflow at the wind ring. Large particles directly fall onto the grinding plate for re grinding. When the materials in the airflow pass through the dynamic and static separators, under the action of the rotating rotor, the coarse powder falls onto the grinding plate for re grinding. The qualified fine powder is grinded together with the airflow, The product is collected in the powder collecting device. Materials containing water are dried in the process of contacting with hot gas to reach the required product moisture.
Technical DATA

Equipment advantages

1. Large production capacity, low energy consumption, and environmental protection.

2. The roll sleeve of the vertical coal mill can be turned over for use, which is not only conducive to improving the output of the coal mill, but also can reduce wear and prolong its service life.

3. Install explosion-proof devices to ensure safe production. The upper shell is equipped with an explosion-proof valve to prevent the explosion of pulverized coal in the mill and ensure the safe use of the equipment.

4. The foot disc shaped grinding plate and tyre shaped roller sleeve adopted by the vertical coal mill are more suitable for coal grinding.

5. The roller bearing does not require special sealing. The grinding roller device adopts a pair of self-aligning roller bearings, and the bearing sealing chamber extends outside the casing, without contacting with dust containing gas. Therefore, simple sealing can prevent the grinding roller bearing from entering dust, and no sealing fan is required.

6. The transmission part of the vertical pulverizer does not need an auxiliary transmission device.

7. The slag removal part is simple. The coal vertical mill has less slag discharge, and the slag discharge port is equipped with a cover plate, so it is unnecessary to install a slag discharge valve.

After-sale service

We have a long-term service in the production line, good technology, responsible after-sales service team. All members have more than 5 years of experience and can provide customers with timely, efficient, comprehensive and scientific after-sales service. It can provide customers with the whole process of after-sales service from engineering construction, production line equipment installation, production line commissioning to production line reaching the standard, solve various difficulties and miscellaneous problems encountered by customers, and provide thoughtful, meticulous and perfect after-sales service.