MSP430F5529IPNR MSP430F6736IPZR MSP430FR2033IG48R MSP430FR2111IRLLR Microcontroller Integrated Circuit

MSP430F5529IPNR MSP430F6736IPZR MSP430FR2033IG48R MSP430FR2111IRLLR Microcontroller Integrated Circuit

1 Features

• Low Supply Voltage Range: 3.6 V Down to 1.8 V

• Ultra-Low Power Consumption

  • – Active Mode (AM):

    – All System Clocks Active:

    • – 290 μA/MHz at 8 MHz, 3.0 V, Flash

      Program Execution (Typical)

    • – 150 μA/MHz at 8 MHz, 3.0 V, RAM

      Program Execution (Typical)

  • – Standby Mode (LPM3):

– Real-Time Clock (RTC) With Crystal, Watchdog, and Supply Supervisor Operational, Full RAM Retention, Fast Wakeup:

– 1.9 μA at 2.2 V, 2.1 μA at 3.0 V (Typical) – Low-Power Oscillator (VLO), General-

Purpose Counter, Watchdog, and Supply Supervisor Operational, Full RAM Retention, Fast Wakeup:
– 1.4 μA at 3.0 V (Typical)

– Off Mode (LPM4):
– Full RAM Retention, Supply Supervisor

Operational, Fast Wakeup:

– 1.1 μA at 3.0 V (Typical) – Shutdown Mode (LPM4.5):

– 0.18 μA at 3.0 V (Typical)

• Wake up From Standby Mode in 3.5 μs (Typical)

• 16-Bit RISC Architecture, Extended Memory, up to

  25-MHz System Clock

• Flexible Power-Management System

  • – Fully Integrated LDO With Programmable Regulated Core Supply Voltage

  • – Supply Voltage Supervision, Monitoring, and Brownout

• Unified Clock System

  • – FLL Control Loop for Frequency Stabilization

  • – Low-Power Low-Frequency Internal Clock

    Source (VLO)

     

2 Applications

• Analog and Digital Sensor Systems

• Data Loggers

• – Low-Frequency Trimmed Internal Reference Source (REFO)

• – 32-kHz Watch Crystals (XT1)

• – High-Frequency Crystals up to 32 MHz (XT2) • 16-Bit Timer TA0, Timer_A With Five

  Capture/Compare Registers
  • 16-Bit Timer TA1, Timer_A With Three

  Capture/Compare Registers
  • 16-Bit Timer TA2, Timer_A With Three

  Capture/Compare Registers
  • 16-Bit Timer TB0, Timer_B With Seven

  Capture/Compare Shadow Registers
  • Two Universal Serial Communication Interfaces

  – USCI_A0 and USCI_A1 Each Support:

  • – Enhanced UART Supports Automatic Baud-

    Rate Detection

  • – IrDA Encoder and Decoder

  • – Synchronous SPI

    – USCI_B0 and USCI_B1 Each Support: – I2C

    – Synchronous SPI
    • Full-Speed Universal Serial Bus (USB)

    – Integrated USB-PHY
    – Integrated 3.3-V and 1.8-V USB Power System – Integrated USB-PLL
    – Eight Input and Eight Output Endpoints

    • 12-Bit Analog-to-Digital Converter (ADC) (MSP430F552x Only) With Internal Reference, Sample-and-Hold, and Autoscan Feature

    • Comparator
    • Hardware Multiplier Supports 32-Bit Operations • Serial Onboard Programming, No External

    Programming Voltage Needed
    • 3-Channel Internal DMA
    • Basic Timer With RTC Feature
    • Device Comparison Summarizes Available Family

    Members

    • Connection to USB Hosts

The TI MSP430TM family of ultra-low-power microcontrollers consists of several devices featuring peripheral sets targeted for a variety of applications. The architecture, combined with extensive low-power modes, is optimized to achieve extended battery life in portable measurement applications. The microcontroller features a powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency. The digitally controlled oscillator (DCO) allows the devices to wake up from low-power modes to active mode in 3.5 μs (typical).

The MSP430F5529, MSP430F5527, MSP430F5525, and MSP430F5521 microcontrollers have integrated USB and PHY supporting USB 2.0, four 16-bit timers, a high-performance 12-bit analog-to-digital converter (ADC), two USCIs, a hardware multiplier, DMA, an RTC module with alarm capabilities, and 63 I/O pins. The MSP430F5528, MSP430F5526, MSP430F5524, and MSP430F5522 microcontrollers include all of these peripherals but have 47 I/O pins.

The MSP430F5519, MSP430F5517, and MSP430F5515 microcontrollers have integrated USB and PHY supporting USB 2.0, four 16-bit timers, two USCIs, a hardware multiplier, DMA, an RTC module with alarm capabilities, and 63 I/O pins. The MSP430F5514 and MSP430FF5513 microcontrollers include all of these peripherals but have 47 I/O pins.

Typical applications include analog and digital sensor systems, data loggers, and others that require connectivity to various USB hosts.

For complete module descriptions, see the MSP430F5xx and MSP430F6xx Family User's Guide

Device Information