High Temperature Transformer Epoxy Resin And Hardener Electrical Insulation White
|
High Temperature Transformer Epoxy Resin And Hardener Electrical Insulation White CE ELECTRICAL INSULATION CASTING EPOXY RESIN AND HARDENER FOR DRY TYPE TRANSFORMERS MSDS:
Tensile strength ISO R 527: 1993 N/mm² 75 - 78 Elongation at break % 1.0 - 1.5 E modulus from tensile test N/mm² 10000 - 12000
Flexural strength ISO 178: 2001 MPa 105 - 115 Surface strain % 1.5 - 2.0 E modulus MPa 8000 - 9500
Critical stress intensity factor (K IC ) MPa·m ½ 2.4 - 2.6
Glass transition temperature ISO 11357-2: 1999°C 85 - 95
Coefficient of linear thermal expansion ISO 11359: 1999 Mean value below Tg ppm/K 65 - 75
Water absorption (specimen: 50x50x4 cm) ISO 62 60 min at 100°C % by wt. 0.43 - 0.47
Density at 20°C g/cm³ 1.65 – 1.75 Thermal life Class (20000h)
Electrical Properties (guideline values)
Breakdown strength IEC 60243-1,50 Hz kV/mm 22 - 25
Industrial hygiene Follow the industrial hygiene standards when operating and processing products For more information, please refer to the corresponding safety data sheet and
Operating protection measures
Workplace safety measures: Protective clothing Need Gloves Must need Arms to protection May contact with the skin, Recommended Goggles/safety glasses Need Mask/dust mask Recommended
Skin protection: Before working To exposed skin protection by cream After washing Frost of besmear protective cream or nutrition Contamination of the skin clean With suction paper wipe, wash with warm water and alkali free soap, With a one-time towel dry. Do not use solvents. Clean workshop environment Use a light paper covering the table and chairs. Using a disposable beaker, etc. Spatter material processing Use sawdust or waste cotton silk blotting, and placed in a plastic woven baskets. Ventilation: To workshop Take a breath three to five times per hour. To position Cover of exhaust fan. The operator should avoid inhalation of vapour.
First aid When the eyes by resin and curing agent and the contamination of castable, immediately with a clean, running water rinse 10 to 15 minutes. To see a doctor. Touch or splash on the skin material to erase, and then clean with water pollution areas (see above). If severe pain or burn, please see the doctor. Replace the dirty clothes immediately. Discomfort caused by inhalation of vapors, remove outdoor immediately. If in doubt, please inquire the medical help. Last revised:2016-01
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Product Tags: High Temperature Transformer Epoxy Resin Electrical Insulation Transformer Epoxy Resin |
![]() |
Hot-curing Cast Resin System Transformer Epoxy Resin For F Thermal Class Indoor And Outdoor Voltage Transformers |
![]() |
Electrical Insulator Coating Solutions Indoor and Outdoor Epxoy Resin with Density 25C 1.19-1.22 g/cm3 |
![]() |
Conventional Vacuum Self Gravity Casting Transformer Epoxy Resin with 12 Months Storage Life 25C and Processing Methods |
![]() |
Vapor Pressure 20°C 0.01 Pa Knudsen Perfect For Medium And High Pressure Current Transformer Indoor |
![]() |
1.15–1.25 G/cm3 Density Hardener Epoxy Resin Transformer With Mould Temperature 70-80C |
![]() |
High Temperature Transformer Epoxy Resin For Conventional Vacuum Casting |