Hotel Movable Folding Partition Walls With Aluminum Trolley And Ceiling Tracks
|
|
Hotel Movable Folding Partition Wall with Aluminum Trolley and Ceiling Tracks
How to operate the folding partition walls
All operations should be gentle and should pay attention to safety. Facing the screen station, use both hands to grab the screen and pull the screen in the direction of the rails; turn the screen in the direction of the rails.
After pushing the screen to its place, fix the screen. Tip: When pushing the screen to the intersection, you should pay attention to the direction of the rail, and then gently push the screen along the rail to the position where it should be placed.
Second, how to fix a multi-directional partition
Hold the partition with one hand, and put the handle in the hexagonal steel at 1100mm of screen side material (the position shown in Figure 3) in the other hand. Hold the handle and turn it clockwise by 180 degrees (or continuously shake). ;, The telescopic seal inside the screen will pop up to fix the screen. Insert the handle into the groove on the side of the screen, and pull the handle upwards to open the expansion screen inside the screen to fix the screen. After the entire group of screens are placed, check whether the screen is straight, whether it is on the same plane as the rails, and if it is not straight, retract the upper and lower expansion seals until the screen is flat.
Third, how to operate multi-directional telescopic panel screen
Normally, the last side of each group of screens is a retractable screen. Push the screen to the position where it should be placed. Then move the handle up and down in the side material groove to pop up and down the active seal (as shown in Figure 1). Show the position), then put the handle in the operation hole on the surface of the expansion screen (the position shown in Figure 2), and turn it counterclockwise until the side of the telescopic aluminum plate is pressed against the wall.
Fourth, how to operate the multi-directional screen door in door
Push the door in the door to the position where it should be placed and the screen in front is tight. Insert the handle into the groove on the side of the screen (as shown in Figure 4), and pull the handle upwards to open the air-seal seal screen on the inner side of the screen. Open the small door, insert the handle into the operation hole of the door leg on the other side of the screen (as shown in Fig. 5), and pull the handle upwards to open the expansion screen on the other side of the screen to fix the screen.
V. How to receive multi-directional screens
1. If there is a door in the door, first turn the square hole on both sides of the door to rotate 180 degrees, loosen the upper and lower seals through the transmission wheel, and then close the door in the door;
2, open the last screen of the telescopic aluminum plate and the upper and lower seals;
3. Retract the telescopic aluminum plate of the last screen so that the distance it produces can at least turn the distance of the screen, which is generally about 140mm.
4. Push the screen to the position of the screen in the direction of the track.
5. After each group of screens is collected in the same way, press each two screens tightly to minimize the distance between the screens and the screens. If necessary, you can open the up and down motion seals of the last screen that is housed at the hidden plate so that it presses against the rails and the ground. This will prevent others from easily pulling the screen out.
What is the door in doors
With the renovation of hotels, restaurants, tea houses, and modern and simple office meeting rooms, the practicality of the event partition has gradually become popular and widely used. In the daily partitions, it is inevitable that you will need to use the door in the door, so that there is a passage in the separated space. We will now introduce the door in the middle of the partition.
The so-called door in the door, is to open a set of small doors in the partition door to facilitate access. There are two kinds of conventional door doors, one is a single door, and the other is a double door.
Single pass door is generally 700-800mm wide and 2100mm high; double door is 1600mm wide and 2100mm high.The door door trim can be unified according to the ordinary door panel decoration, but in some cases, the door door needs to do a separate style.
Rolling partition walls
Assembled activity partition
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Product Tags: acoustic folding partition soundproof folding partition | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Acoustic Movable Office Partition Walls In Leather Surface For Hotel Hall |
|
Laminate Veneer Sound Proof High Folding Partition Walls For Office Classroom |
|
Office Acoustic Folding Door Removable Partition Walls For Meeting Room |
|
Conference Hall Acoustic Folding Room Partition Walls Commercial |
|
Removable Wooden Hanging Folding Partition Walls In Philippines |
|
Commercial Sound Absorbing Folding Partition Door With Pass Door |