MQM8790 HS2F Mellanox Switches 40 ports smart rack mountable HDR
InfiniBand Switch Mellanox Quantum QM8790 - switch - 40 ports - smart -
rack-mountable Built with Quantum InfiniBand switch device, Mellanox MQM8790-HS2F
provides 40x HDR 200G QSFP56 ports, and each QSFP56 port can be
configured as 2x HDR100 100G via breakout cables. The switch
provides the highest performing fabric solution in a 1U form factor
by delivering up to 16Tb/s of non-blocking bandwidth with sub 130ns
port-to-port latency. MQM8790-HS2F enables efficient computing with features such as
static routing, adaptive routing, congestion control and enhanced
VL mapping to enable modern topologies (SlimFly, Dragonfly+, 6DT).
These ensure the maximum effective fabric bandwidth by eliminating
congestion hot spots. | Model | MQM8790-HS2F | | Ports | 40x 200G QSFP56 | | Switching Capacity | 16 Tbps | | CPU | Broadwell ComEx D-1508 2.2GHZ | | Forwarding Rate | 7,200 Mpps | | Software | MLNX-OS | | System Memory | Single 8GB | | Typical Power Consumption | 224W | | Latency | 130ns | | Max. Power Consumption | 740W |
Our stock support good price C9115AXI-E Specification | | Description | Cisco Catalyst 9115AX Series Access Point, Internal antenna; Wi-Fi
6; 4x4:4 MIMO, E Domain | | Software | ● Cisco Unified Wireless Network Software Release 8.9 or later ● Cisco IOS ® XE Software Release 16.11 or later | | Supported wireless LAN controllers | ● Cisco Catalyst 9800 Series Wireless Controllers ● Cisco 3500, 5520, and 8540 Series Wireless Controllers and Cisco
Virtual Wireless Controller | | 802.11n version 2.0 (and related) capabilities | ● 4x4 MIMO with four spatial streams ● Maximal Ratio Combining (MRC) ● 802.11n and 802.11a/g beamforming ● 20- and 40-MHz channels ● PHY data rates up to 890 Mbps (40 MHz with 5 GHz and 20 MHz with
2.4 GHz) ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU
(transmit and receive) ● 802.11 Dynamic Frequency Selection (DFS) ● Cyclic Shift Diversity (CSD) support | | 802.11ac | ● 4x4 downlink MU-MIMO with four spatial streams ● MRC ● 802.11ac beamforming ● 20-, 40-, 80-, and 160-MHz channels ● PHY data rates up to 3.47 Gbps (160 MHz with 5 GHz) ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU
(transmit and receive) ● 802.11 DFS ● CSD support | | 802.11ax | ● 4x4 downlink MU-MIMO with four spatial streams ● Uplink/downlink OFDMA ● TWT ● BSS coloring ● MRC ● 802.11ax beamforming ● 20-, 40-, 80-, and 160-MHz channels ● PHY data rates up to 5.38 Gbps (160 MHz with 5 GHz and 20 MHz
with 2.4 GHz) ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU
(transmit and receive) ● 802.11 DFS ● CSD support | | Integrated antenna | ● 2.4 GHz, peak gain 3 dBi, internal antenna, omnidirectional in
azimuth ● 5 GHz, peak gain 4 dBi, internal antenna, omnidirectional in
azimuth | | External antenna (sold separately) | ● Cisco Catalyst 9115AXE Access Points are certified for use with
antenna gains up to 6 dBi (2.4 GHz and 5 GHz) ● Cisco offers the industry's broadest selection of antennas,
delivering optimal coverage for a variety of deployment scenarios | | Interfaces | ● 1x 100, 1000, 2500 Multigigabit Ethernet (RJ-45) – IEEE 802.3bz ● Management console port (RJ-45) ● USB 2.0 (enabled via future software) | | Indicators | ● Status LED indicates boot loader status, association status,
operating status, boot loader warnings, and boot loader errors | | Dimensions (W x L x H) | ● Access point (without mounting brackets): C9115I: 8.0 x 8.0 x 1.5
in. (20.3 x 20.3 x 3.8 cm), C9115E: 8.0 x 8.0 x 1.7 in. (20.3 x
20.3 x 4.3 cm) | | Input power requirements | ● 802.3at Power over Ethernet Plus (PoE+), 802.3bt Cisco Universal
PoE (Cisco UPOE+, Cisco UPOE ®) ● Cisco power injector, AIR-PWRINJ6= ● 802.3af PoE ● Cisco power injector, AIR-PWRINJ5= (Note: This injector supports
only 802.3af) Note: When 802.3af PoE is the source of power, both 2.4-GHz and
5-GHz radios will be reduced to 2x2 and Ethernet downgraded to 1
Gigabit Ethernet. In addition, the USB port will be off. | | Environmental | Cisco Catalyst 9115AXI ● Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C) ● Nonoperating (storage) altitude test: 25˚C, 15,000 ft. ● Operating temperature: 32° to 122°F (0° to 50°C) ● Operating humidity: 10% to 90% (noncondensing) ● Operating altitude test: 40˚C, 9843 ft. Note: When the ambient operating temperature exceeds 40°C, the
access point will shift from 4x4 to 2x2 on both the 2.4-GHz and
5-GHz radios, uplink Ethernet will downgrade to 1 Gigabit Ethernet,
and the USB interface will be disabled. Cisco Catalyst 9115AXE ● Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C) ● Nonoperating (storage) altitude test: 25˚C, 15,000 ft. ● Operating temperature: -4° to 122°F (-20° to 50°C) ● Operating humidity: 10% to 90% (noncondensing) ● Operating altitude test: 40˚C, 9843 ft. | | System memory | ● 2048 MB DRAM ● 1024 MB flash | | Available transmit power settings | 2.4 GHz ● 23 dBm (200 mW) ● 20 dBm (100 mW) ● 17 dBm (50 mW) ● 14 dBm (25 mW) ● 11 dBm (12.5 mW) ● 8 dBm (6.25 mW) ● 5 dBm (3.13 mW) ● 2 dBm (1.56 mW) ● -1dBm (0.79mW) ● -4dBm (0.39mW) 5 GHz ● 23 dBm (200 mW) ● 20 dBm (100 mW) ● 17 dBm (50 mW) ● 14 dBm (25 mW) ● 11 dBm (12.5 mW) ● 8 dBm (6.25 mW) ● 5 dBm (3.13 mW) ● 2 dBm (1.56 mW) ● -1dBm (0.79mW) ● -4dBm (0.39mW) | | Frequency band and 20-MHz operating channels | E (E regulatory domain): ● 2.412 to 2.472 GHz; 13 channels
● 5.180 to 5.320 GHz; 8 channels
● 5.500 to 5.700 GHz; 8 channels
(excludes 5.600 to 5.640 GHz) |
C9115AXI-E Specification | | Description | Cisco Catalyst 9115AX Series Access Point, Internal antenna; Wi-Fi
6; 4x4:4 MIMO, E Domain | | Software | ● Cisco Unified Wireless Network Software Release 8.9 or later ● Cisco IOS ® XE Software Release 16.11 or later | | Supported wireless LAN controllers | ● Cisco Catalyst 9800 Series Wireless Controllers ● Cisco 3500, 5520, and 8540 Series Wireless Controllers and Cisco
Virtual Wireless Controller | | 802.11n version 2.0 (and related) capabilities | ● 4x4 MIMO with four spatial streams ● Maximal Ratio Combining (MRC) ● 802.11n and 802.11a/g beamforming ● 20- and 40-MHz channels ● PHY data rates up to 890 Mbps (40 MHz with 5 GHz and 20 MHz with
2.4 GHz) ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU
(transmit and receive) ● 802.11 Dynamic Frequency Selection (DFS) ● Cyclic Shift Diversity (CSD) support | | 802.11ac | ● 4x4 downlink MU-MIMO with four spatial streams ● MRC ● 802.11ac beamforming ● 20-, 40-, 80-, and 160-MHz channels ● PHY data rates up to 3.47 Gbps (160 MHz with 5 GHz) ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU
(transmit and receive) ● 802.11 DFS ● CSD support | | 802.11ax | ● 4x4 downlink MU-MIMO with four spatial streams ● Uplink/downlink OFDMA ● TWT ● BSS coloring ● MRC ● 802.11ax beamforming ● 20-, 40-, 80-, and 160-MHz channels ● PHY data rates up to 5.38 Gbps (160 MHz with 5 GHz and 20 MHz
with 2.4 GHz) ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU
(transmit and receive) ● 802.11 DFS ● CSD support | | Integrated antenna | ● 2.4 GHz, peak gain 3 dBi, internal antenna, omnidirectional in
azimuth ● 5 GHz, peak gain 4 dBi, internal antenna, omnidirectional in
azimuth | | External antenna (sold separately) | ● Cisco Catalyst 9115AXE Access Points are certified for use with
antenna gains up to 6 dBi (2.4 GHz and 5 GHz) ● Cisco offers the industry's broadest selection of antennas,
delivering optimal coverage for a variety of deployment scenarios | | Interfaces | ● 1x 100, 1000, 2500 Multigigabit Ethernet (RJ-45) – IEEE 802.3bz ● Management console port (RJ-45) ● USB 2.0 (enabled via future software) | | Indicators | ● Status LED indicates boot loader status, association status,
operating status, boot loader warnings, and boot loader errors | | Dimensions (W x L x H) | ● Access point (without mounting brackets): C9115I: 8.0 x 8.0 x 1.5
in. (20.3 x 20.3 x 3.8 cm), C9115E: 8.0 x 8.0 x 1.7 in. (20.3 x
20.3 x 4.3 cm) | | Input power requirements | ● 802.3at Power over Ethernet Plus (PoE+), 802.3bt Cisco Universal
PoE (Cisco UPOE+, Cisco UPOE ®) ● Cisco power injector, AIR-PWRINJ6= ● 802.3af PoE ● Cisco power injector, AIR-PWRINJ5= (Note: This injector supports
only 802.3af) Note: When 802.3af PoE is the source of power, both 2.4-GHz and
5-GHz radios will be reduced to 2x2 and Ethernet downgraded to 1
Gigabit Ethernet. In addition, the USB port will be off. | | Environmental | Cisco Catalyst 9115AXI ● Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C) ● Nonoperating (storage) altitude test: 25˚C, 15,000 ft. ● Operating temperature: 32° to 122°F (0° to 50°C) ● Operating humidity: 10% to 90% (noncondensing) ● Operating altitude test: 40˚C, 9843 ft. Note: When the ambient operating temperature exceeds 40°C, the
access point will shift from 4x4 to 2x2 on both the 2.4-GHz and
5-GHz radios, uplink Ethernet will downgrade to 1 Gigabit Ethernet,
and the USB interface will be disabled. Cisco Catalyst 9115AXE ● Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C) ● Nonoperating (storage) altitude test: 25˚C, 15,000 ft. ● Operating temperature: -4° to 122°F (-20° to 50°C) ● Operating humidity: 10% to 90% (noncondensing) ● Operating altitude test: 40˚C, 9843 ft. | | System memory | ● 2048 MB DRAM ● 1024 MB flash | | Available transmit power settings | 2.4 GHz ● 23 dBm (200 mW) ● 20 dBm (100 mW) ● 17 dBm (50 mW) ● 14 dBm (25 mW) ● 11 dBm (12.5 mW) ● 8 dBm (6.25 mW) ● 5 dBm (3.13 mW) ● 2 dBm (1.56 mW) ● -1dBm (0.79mW) ● -4dBm (0.39mW) 5 GHz ● 23 dBm (200 mW) ● 20 dBm (100 mW) ● 17 dBm (50 mW) ● 14 dBm (25 mW) ● 11 dBm (12.5 mW) ● 8 dBm (6.25 mW) ● 5 dBm (3.13 mW) ● 2 dBm (1.56 mW) ● -1dBm (0.79mW) ● -4dBm (0.39mW) | | Frequency band and 20-MHz operating channels | E (E regulatory domain): ● 2.412 to 2.472 GHz; 13 channels
● 5.180 to 5.320 GHz; 8 channels
● 5.500 to 5.700 GHz; 8 channels
(excludes 5.600 to 5.640 GHz) |
C9115AXI-E Specification | | Description | Cisco Catalyst 9115AX Series Access Point, Internal antenna; Wi-Fi
6; 4x4:4 MIMO, E Domain | | Software | ● Cisco Unified Wireless Network Software Release 8.9 or later ● Cisco IOS ® XE Software Release 16.11 or later | | Supported wireless LAN controllers | ● Cisco Catalyst 9800 Series Wireless Controllers ● Cisco 3500, 5520, and 8540 Series Wireless Controllers and Cisco
Virtual Wireless Controller | | 802.11n version 2.0 (and related) capabilities | ● 4x4 MIMO with four spatial streams ● Maximal Ratio Combining (MRC) ● 802.11n and 802.11a/g beamforming ● 20- and 40-MHz channels ● PHY data rates up to 890 Mbps (40 MHz with 5 GHz and 20 MHz with
2.4 GHz) ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU
(transmit and receive) ● 802.11 Dynamic Frequency Selection (DFS) ● Cyclic Shift Diversity (CSD) support | | 802.11ac | ● 4x4 downlink MU-MIMO with four spatial streams ● MRC ● 802.11ac beamforming ● 20-, 40-, 80-, and 160-MHz channels ● PHY data rates up to 3.47 Gbps (160 MHz with 5 GHz) ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU
(transmit and receive) ● 802.11 DFS ● CSD support | | 802.11ax | ● 4x4 downlink MU-MIMO with four spatial streams ● Uplink/downlink OFDMA ● TWT ● BSS coloring ● MRC ● 802.11ax beamforming ● 20-, 40-, 80-, and 160-MHz channels ● PHY data rates up to 5.38 Gbps (160 MHz with 5 GHz and 20 MHz
with 2.4 GHz) ● Packet aggregation: A-MPDU (transmit and receive), A-MSDU
(transmit and receive) ● 802.11 DFS ● CSD support | | Integrated antenna | ● 2.4 GHz, peak gain 3 dBi, internal antenna, omnidirectional in
azimuth ● 5 GHz, peak gain 4 dBi, internal antenna, omnidirectional in
azimuth | | External antenna (sold separately) | ● Cisco Catalyst 9115AXE Access Points are certified for use with
antenna gains up to 6 dBi (2.4 GHz and 5 GHz) ● Cisco offers the industry's broadest selection of antennas,
delivering optimal coverage for a variety of deployment scenarios | | Interfaces | ● 1x 100, 1000, 2500 Multigigabit Ethernet (RJ-45) – IEEE 802.3bz ● Management console port (RJ-45) ● USB 2.0 (enabled via future software) | | Indicators | ● Status LED indicates boot loader status, association status,
operating status, boot loader warnings, and boot loader errors | | Dimensions (W x L x H) | ● Access point (without mounting brackets): C9115I: 8.0 x 8.0 x 1.5
in. (20.3 x 20.3 x 3.8 cm), C9115E: 8.0 x 8.0 x 1.7 in. (20.3 x
20.3 x 4.3 cm) | | Input power requirements | ● 802.3at Power over Ethernet Plus (PoE+), 802.3bt Cisco Universal
PoE (Cisco UPOE+, Cisco UPOE ®) ● Cisco power injector, AIR-PWRINJ6= ● 802.3af PoE ● Cisco power injector, AIR-PWRINJ5= (Note: This injector supports
only 802.3af) Note: When 802.3af PoE is the source of power, both 2.4-GHz and
5-GHz radios will be reduced to 2x2 and Ethernet downgraded to 1
Gigabit Ethernet. In addition, the USB port will be off. | | Environmental | Cisco Catalyst 9115AXI ● Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C) ● Nonoperating (storage) altitude test: 25˚C, 15,000 ft. ● Operating temperature: 32° to 122°F (0° to 50°C) ● Operating humidity: 10% to 90% (noncondensing) ● Operating altitude test: 40˚C, 9843 ft. Note: When the ambient operating temperature exceeds 40°C, the
access point will shift from 4x4 to 2x2 on both the 2.4-GHz and
5-GHz radios, uplink Ethernet will downgrade to 1 Gigabit Ethernet,
and the USB interface will be disabled. Cisco Catalyst 9115AXE ● Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C) ● Nonoperating (storage) altitude test: 25˚C, 15,000 ft. ● Operating temperature: -4° to 122°F (-20° to 50°C) ● Operating humidity: 10% to 90% (noncondensing) ● Operating altitude test: 40˚C, 9843 ft. | | System memory | ● 2048 MB DRAM ● 1024 MB flash | | Available transmit power settings | 2.4 GHz ● 23 dBm (200 mW) ● 20 dBm (100 mW) ● 17 dBm (50 mW) ● 14 dBm (25 mW) ● 11 dBm (12.5 mW) ● 8 dBm (6.25 mW) ● 5 dBm (3.13 mW) ● 2 dBm (1.56 mW) ● -1dBm (0.79mW) ● -4dBm (0.39mW) 5 GHz ● 23 dBm (200 mW) ● 20 dBm (100 mW) ● 17 dBm (50 mW) ● 14 dBm (25 mW) ● 11 dBm (12.5 mW) ● 8 dBm (6.25 mW) ● 5 dBm (3.13 mW) ● 2 dBm (1.56 mW) ● -1dBm (0.79mW) ● -4dBm (0.39mW) | | Frequency band and 20-MHz operating channels | E (E regulatory domain): ● 2.412 to 2.472 GHz; 13 channels
● 5.180 to 5.320 GHz; 8 channels
● 5.500 to 5.700 GHz; 8 channels
(excludes 5.600 to 5.640 GHz) |
| C1000-48P-4G-L | C9500-NM-8X | CAB-SPWR-30CM | | C1000-48T-4G-L | C9800-F-X-K9 | C9200L-STACK-KIT | | WS-C2960X-24TS-LL | N9K-C93180YC-FX | PWR-C4-950WAC-R | | WS-C2960X-24PSQ-L | N3K-C3172PQ-XL | C9200-NM-4G | | WS-C2960X-24PS-L | N2K-C2348UPQ | C9200-NM-4X | | WS-C2960X-48TS-L | AIR-AP1832I-H-K9 | C9300-NM-4G | | WS-C2960L-24PS-AP | AIR-AP2802I-H-K9 | C9300-NM-8X | | WS-C2960L-16TS-LL | C9115AXI-H | GLC-LH-SMD | | WS-C2960L-8TS-LL | C9120AXI-H | SFP-10G-SR | | WS-C3560-48FS-S | AIR-AP1562I-H-K9 | SFP-10G-LR | | WS-C2960X-24PS-L | AIR-AP1562D-H-K9 | SFP-10G-SR-S | | C9200L-48P-4X-E | C9800-L-C-K9 | SFP-10G-LR-S | | C9200L-48P-4G-E | C9800-L-F-K9 | GLC-TE | | C9200L-24T-4G-E | AP505 | SFP-H10GB-CU2M | | C9300-24T-A | AP515 | MA-CBL-40G-3M | | C9300-48T-A | CP-3905 | GLC-LH-SMD= | | C9300-24S-A | CP-7821-K9 | ISR4331/K9 | | C9300-48S-A | CP-8832-MIC-WIRED | ISR4331/K9 RF | | C9300-48P-E | CS-MIC-TABLE-J | FPR2110-ASA-K9 | | C9300-24P-E | AIR-AP3802I-E-K9 | FPR2110-ASA-K9 | | C9300L-24T-4G-E | C1111-8P | FPR2120-ASA-K9 | | C9300L-48T-4G-E | PWR-C5-125WAC | FPR2130-ASA-K9 | | C9300-NM-8X | PWR-C5-1KWAC | C9200-NM-4G= | | C9400-LC-24S | PWR-C6-125WAC | C9200-NM-4G= | | C9400-LC-48S | STACK-T1-50CM | C9200L-24P-4G-CE | | C9500-24Y4C-A | STACK-T1-1M | C9200L-24P-4G-CE | | C9500-48Y4C-A | STACK-T1-3M | C9200L-48P-4G-E |
|
