Separator - Centrifuge , Structure Auto Diesel Fuel Cleaner

Separator - Centrifuge, Structure Auto Diesel Fuel Cleaner

Description

Model PDSD4000P-B1217Z separator is mainly used to remove water and mechanical impurities from diesel oil, lubricating oil, and other mineral oil in marine diesel engine units and land-used diesel generator unit of power station so as to reduce wear of the diesel engine and other machines, and prolong engine life.

The model is also used to separate two unsolvable liquids with different specific gravity or remove a small amount of solid particles from the liquid.        

The machine adopts automatic control and has the advantages of high efficiency, low oil consumption, convenient operation, and economic maintenance cost.   

The clear oil and dirty water are pumped out by a centripetal pump, the sludge is discharged automatically and fully. 

The machine is one kind of rotary machine with high speed. After accurate dynamic balancing, it can run for a long time with low vibration, safety, and security.

The design, product, and acceptance are conformed to the standard of GB/T5745 “Marine Disc Separator”. 

Advantages

1. Controlled by touch panel and PLC program, with both Chinese and English operation interface.
2. Automatically control the sealing discharging process of the separator, manual operation also allowed, parameters-setting by the panel.
3. equipped with high temperature, low pressure, motor overload, and oil pump overload.
4. automatically switch the oil way after the alarm.
5. Installed a dry contact to deliver an alarm signal(One of the oil separators can function as diesel oil standby).
6. The cabinet is equipped with an hour totalizer.

Main Technical Specification

The Whole Unit Consists of

1. Separator   2. Screw pump   3.Electric control box  4. Steam heater  5. Temperature adjusting valve 6. High-temperature ball valve  7. Steam trap  8. Temperature sensor  9. Pneumatic Three-way valve    10. Stop-check valve  11. Oil filter 12. Vacuum gauge 13. Pressure gauge 14. Air pressure reducing valve15. 3/2 Solenoid valve  16. Ball valve  17. Brass filter ball valve   18. Water pressure reducing valve 19. 2/2 Solenoid valve  20. 2/2 Solenoid valve  21. Pressure switch   22. Moisture sensor  23.Skid
           

Condition for mineral oil separation and actual capacity (refer to the chart)

Value Analysis

1. According to the requirements of each classification society, all modules are equipped with oil leak alarms and high-temperature alarms.
2. Oil. hydraulic, pneumatic control part adopts the Brand Baode (Germany).

3. Heater adopts the brand SWEP (Germany).

4. Pressure control adopts Korean products or products

5.  Screw pump is used instead of gear pump.

6. All are equipped with automatic temperature control devices (Made by RTK production in Germany or made in China)
7. The main electrical components of the standard electrical control box are produced by Schneider company while PLC is produced by Siemens or Mitsubishi.
8. The complete sets referred to above are all Peony's production of automatic Standard Controls and we certainly can modify the configuration list according to customers’ specified requirements.

Peony organizes the model selection question below

1)How many kinds of oil can you separate?
This series separator is widely used for different kinds of oils, especially for Marine diesel oil and similar oils, such as light fuel oil, heavy fuel oil, lubrication oil, steam turbine oil, detergence oil, engine oil, etc.

2)How can you select a suitable capacity?
Different oil has different capacity, our 1500L, 2000L, 3000L, 4000L, 5000L, 6000L, 8000L ,10000L capacity is for the Marine diesel oil 0# as sample. It also depends on the viscidity and temperature, and for all the capacity models, we have an oil characteristic sheet to help our customers find out what their oil is, and what capacity their oil belongs to.

3) Is your separator self-cleaning?
We have 3 types of discharge means according to different materials and customers' requirements, we have a self-cleaning model and a manual cleaning model.
1. Manual discharge model for the oil with very less solid component
2. Full discharge model for the big capacity treatment and a little solid component
3. Partly discharge model for the bigger capacity treatment and more solid component

4). Variable discharge model

No.ful discharge type and partial discharge type are both self-cleaning models.
4)Will you help us to select the model?
Yes, you can select the model by yourself, or as long as you provide your material characteristics, we have a professional engineering team to help you select the suitable machine

5)Do you only have a single machine or a unit?
Both we have.

More pictures

Guarantee

Peony Centrifuge has been dedicated to producing machinery and types of equipment and carrying out facility construction, pursuing the best quality and producing the best product at the same time. We are committed to rewarding you with a better quality in return for our interest in and faith. We will do our utmost to one more step forward, based on our infinite services and trust in customers.